Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com

Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com (https://www.camaro5.com/forums/index.php)
-   Camaro 1LE Forum (https://www.camaro5.com/forums/forumdisplay.php?f=149)
-   -   1LE intake headers vmax tb dyno tune results. (https://www.camaro5.com/forums/showthread.php?t=340040)

GR8WHITE1 01-31-2014 08:42 PM

1LE intake headers vmax tb dyno tune results.
 
Had Charlie at rpm motors tune my car today mods are stainless power headers with cats cai intake npp exhaust and vmax ported tb. Laid down 426hp and 416tq here's the graph.http://img.tapatalk.com/d/14/02/01/sesynuta.jpg
Sent from my SPH-L710 using Tapatalk 2

shawn18 01-31-2014 09:25 PM

Nice!


Sent from my iPhone using Tapatalk

eagle1 01-31-2014 10:01 PM

Got to feel good on the road now. Nice

VOGGS-LS3-1LE 01-31-2014 10:24 PM

Headers and a CAI really benefit the ls3. Best results with a tune. Good job!

shawn18 01-31-2014 10:26 PM

Did you get a baseline pull before you did the install & tune?

GR8WHITE1 01-31-2014 11:11 PM

Unfortunately not he's a bit of a ways away so just took it down after the install. Feels like she lost some torque down lower but pulls all the way up top and sounds like a monster with the npp exhaust. Have had a ton of thumbs up and people say it sounds awesome.

Sent from my SPH-L710 using Tapatalk 2

umiami2312 02-01-2014 01:33 AM

this is the exact setup i will have installed in two weeks, i finally get my headers and tune! happy to see the numbers and glad that it still sounds good with the NPP. Just wondering, did you pull your fuse on the exhaust to keep the flaps open all the time? Video if possible?

Msmall143 02-01-2014 02:53 AM

It's really tough to determine gains without a pre install dyno run on the same dyno you did post install. But those are numbers you would expect which is great.

Here's an audio with similiar set up but pfadt headers, intake, tune. No ported tb

http://www.youtube.com/watch?v=PpDkHgqdBvI

I did have a baseline done stock and after install of headers, cai (no scoop) and tune. the performance gain from pfadt headers, cai intake and tune was 43 rwhp. The stock baseline was done right before install, and the post install dyno was done same day immediately after install. Obviously on the same dyno...a Autodyn 30 Dynamometer. Just FYI....it was a 43 rwhp without air

Basically it was 43 rwhp. But I think it's fairer to say 38 rwhp.

I say this because we did 2 passes pre installs and the 4 passes post install. Apples to apples the second post dyno run showed a pick up of 38rwhp when compared to the second pre dyno run.

The gains continued to increase on the post install runs until the 4th and fifth pull which it then leveled out and became consistent at 43 rwhp gain when compared to the highest pre install run (second and last pre install pull)

I have the data points but am having issues plotting them because the software is giving me some issues

I've dynod as low as 376 and as high as 422 with this current setup, just shows how much these dynos vary


All times are GMT -5. The time now is 07:18 PM.

Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2018, vBulletin Solutions, Inc.