Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com
 
Solo Performance
Go Back   Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com > Search Forums


Showing results 1 to 30 of 500
Search took 0.08 seconds.
Search: Posts Made By: ttshovel
Forum: Forced Induction - V8 01-19-2020, 02:42 PM
Replies: 8
Views: 335
Posted By ttshovel
Oh, for sure The cost of a fuel system is...

Oh, for sure

The cost of a fuel system is outrageous!

I'm going cable drive right now and methanol. I bet I have 5k in fuel system alone
Forum: Forced Induction - V8 01-19-2020, 12:37 PM
Replies: 8
Views: 335
Posted By ttshovel
Tkm, tsp, bullet racing engines, golen, lme, mlre...

Tkm, tsp, bullet racing engines, golen, lme, mlre to name a few
Forum: Forced Induction - V8 01-19-2020, 12:05 PM
Replies: 8
Views: 335
Posted By ttshovel
The 5.3, 6.0, and 6.2 all share the same stroke...

The 5.3, 6.0, and 6.2 all share the same stroke crank 3.622

If you want a reliable aluminum block for that power you need to go to a resleeved block, fill your block, or go aftermarket. Just being...
Forum: Forced Induction - V8 01-19-2020, 08:04 AM
Replies: 8
Views: 335
Posted By ttshovel
Just rods, pistons, and main studs will hold good...

Just rods, pistons, and main studs will hold good power for a while. The issue is the liners in the ls3 block.

Best bang for your buck is to find an iron gen 4 6.0, reuse the crank in it, put...
Forum: Forced Induction 01-15-2020, 08:24 PM
Replies: 1
Views: 196
Posted By ttshovel
Forced inductions gt55 94mm

Selling a forced inductions built gt55 94mm, t6 1.12ar. Have had the turbo on my car for half a season. Has dyno time, and about 20 passes on it. Has zero shaft play. Looking to get into a larger...
Forum: Member Car Journals 01-15-2020, 03:21 PM
Replies: 459
Views: 40,453
Posted By ttshovel
Started making panels for the firewall. Will be...

Started making panels for the firewall. Will be making the panel that covers the back of the motor removable to make easy access to trans bolts. Will also use this to mount all my electronics/wiring...
Forum: Forced Induction - V8 01-15-2020, 08:45 AM
Replies: 1
Views: 198
Posted By ttshovel
To my knowledge no one makes a kit. I ran into...

To my knowledge no one makes a kit. I ran into the same issue before biting the bullet.
Forum: Member Car Journals 01-14-2020, 07:45 PM
Replies: 459
Views: 40,453
Posted By ttshovel
Radiator mounted. Hose made for fill. Just need a...

Radiator mounted. Hose made for fill. Just need a few fittings for the feed line. Going to jegs monday to return the rack, get the new, and get a few more odds and ends

Cut the motor plate up some...
Forum: Member Car Journals 01-13-2020, 05:34 PM
Replies: 459
Views: 40,453
Posted By ttshovel
Got the steering column all made, adjuster all...

Got the steering column all made, adjuster all made. Figured out the hard way that I bought a rear steer rack, turn the wheel to the left and it goes right :smiling1::smiling1:

Will be taking that...
Forum: Member Car Journals 01-10-2020, 04:47 AM
Replies: 459
Views: 40,453
Posted By ttshovel
Thank you! Yes, going for straight drag now. I've...

Thank you! Yes, going for straight drag now. I've been on aftermarket standalone for a while now. Fan is just on a toggle
Forum: Member Car Journals 01-09-2020, 07:48 PM
Replies: 459
Views: 40,453
Posted By ttshovel
Got some more parts in. Radiator and fan...

Got some more parts in.

Radiator and fan combo- csf part# 7065. This thing is tiny!
Steering shaft, 2 universals(one for in car is the wrong size), and the passenger side steering rack mount...
Forum: Member Car Journals 01-07-2020, 11:07 AM
Replies: 459
Views: 40,453
Posted By ttshovel
Thanks man! I'm gonna try my best to have it...

Thanks man! I'm gonna try my best to have it completed and making good passes before then!

Got the new rack tacked in. Need to get the passenger side mount made yet.

The tie rod ends I had...
Forum: Member Car Journals 01-05-2020, 05:33 PM
Replies: 459
Views: 40,453
Posted By ttshovel
Thank you! Got the centers of the k members...

Thank you!

Got the centers of the k members cut out, will definitely need new mounts, and an intermediate shaft. Will be picking up a few fittings to clean up the vacuum pump hoses.

Slowly...
Forum: Member Car Journals 01-05-2020, 11:47 AM
Replies: 459
Views: 40,453
Posted By ttshovel
Got the rack, tie rods, and a new cell. Rack...

Got the rack, tie rods, and a new cell.

Rack is flaming river part number FR1507-2
Tie rods are flaming river part number FR1603

Fuel cell is a jegs brand 5 gallon. Part number 555-15384
...
Forum: Member Car Journals 01-04-2020, 02:53 PM
Replies: 459
Views: 40,453
Posted By ttshovel
Absolutely man! The axle housing bare is...

Absolutely man!

The axle housing bare is 37", axle to axle 42", backspace is 4" on a 15x14. To fit that size tire I'd probably go will a 2-3" backspace.
Forum: Dragstrip and Launch Techniques Discussion 01-01-2020, 10:18 AM
Replies: 78
Views: 24,675
Posted By ttshovel
Yeah, they're for drag race use. 30lbs off the...

Yeah, they're for drag race use. 30lbs off the nose would be nice
Forum: Member Car Journals 01-01-2020, 05:58 AM
Replies: 459
Views: 40,453
Posted By ttshovel
Last piece of the front accessories. Will have...

Last piece of the front accessories. Will have front finished this weekend. Hoping its the last time the front motor plate goes on
Forum: Member Car Journals 12-30-2019, 05:05 PM
Replies: 459
Views: 40,453
Posted By ttshovel
Got the fittings all welded in today. Have to cut...

Got the fittings all welded in today. Have to cut up the motor plate a bit more to get it to fit, then from there water pump, radiator, and coolant line plumbing
Forum: Member Car Journals 12-28-2019, 04:05 PM
Replies: 459
Views: 40,453
Posted By ttshovel
More pieces of the puzzle. Going to block off the...

More pieces of the puzzle. Going to block off the water pump ports on the block and weld bungs into the front/back of the heads to prepare for a dry deck motor. The ls2 block will be 100% solid...
Forum: Member Car Journals 12-24-2019, 04:11 PM
Replies: 459
Views: 40,453
Posted By ttshovel
Vacuum pump mounted.

Vacuum pump mounted.
Forum: Member Car Journals 12-22-2019, 06:11 PM
Replies: 459
Views: 40,453
Posted By ttshovel
Pulled the factory power rack and brake booster....

Pulled the factory power rack and brake booster. Going to go with a reverse swing pedal to get plug access on the driver side. Will post up part numbers as I get parts
Forum: Member Car Journals 12-20-2019, 10:56 AM
Replies: 459
Views: 40,453
Posted By ttshovel
Thanks guys! The ring came from titanium buzz....

Thanks guys! The ring came from titanium buzz. They have a bunch of car related ones.

I'm looking forward to it as well! Cant wait to hear it with a legit piping
Forum: Member Car Journals 12-19-2019, 07:31 PM
Replies: 459
Views: 40,453
Posted By ttshovel
Wedding is all done. She got me a badass ring...

Wedding is all done. She got me a badass ring :thumbup:

Cut motor plate apart for accessories. Will be purchasing the rest of it very shortly
Forum: Member Car Journals 12-05-2019, 11:03 PM
Replies: 459
Views: 40,453
Posted By ttshovel
Thanks guys. The fab shop stopped out and we made...

Thanks guys. The fab shop stopped out and we made a list of all the materials needed to make it happen. Hoping to have all that stuff, along with everything else lined out after the holidays and back...
Forum: Member Car Journals 12-05-2019, 02:27 PM
Replies: 459
Views: 40,453
Posted By ttshovel
Turbo tacked in place using the new maven mount....

Turbo tacked in place using the new maven mount. Made life 100% easier mounting it
Forum: Member Car Journals 12-04-2019, 09:11 PM
Replies: 459
Views: 40,453
Posted By ttshovel
Got the midplate and front plate brackets welded...

Got the midplate and front plate brackets welded in.

Got the trans bolted up. Super shocked it fit without any more cutting! showing a negative 3 degree drivetrain angle which is around what I...
Forum: Dragstrip and Launch Techniques Discussion 12-02-2019, 09:10 PM
Replies: 17
Views: 719
Posted By ttshovel
Yes sir! Tons of room now. Fab guy is stopping by...

Yes sir! Tons of room now. Fab guy is stopping by Thursday to measure for materials and start mockup shortly after!
Forum: Dragstrip and Launch Techniques Discussion 11-29-2019, 04:15 PM
Replies: 17
Views: 719
Posted By ttshovel
It all fits! Will be welding mounts in and...

It all fits! Will be welding mounts in and hanging trans this coming week
Forum: Member Car Journals 11-29-2019, 02:37 PM
Replies: 459
Views: 40,453
Posted By ttshovel
Headers fit with plenty of clearance around...

Headers fit with plenty of clearance around everything. Egt bungs and maven turbo mounts came in as well. Next up welding the brackets for the motor plates in
Forum: Dragstrip and Launch Techniques Discussion 11-27-2019, 08:18 PM
Replies: 17
Views: 719
Posted By ttshovel
Should just be a straight 5 inches off and a...

Should just be a straight 5 inches off and a rebalance but I'll remeasure to be sure. Any weight I can get off this 4 inch steel shaft the better lol
Showing results 1 to 30 of 500

 
Forum Jump

All times are GMT -5. The time now is 07:44 PM.


Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2020, vBulletin Solutions, Inc.