Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com
  
Phastek Performance
Go Back   Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com > Search Forums
Reload this Page Search Results
Homepage Garage Wiki Register Community Calendar Today's Posts Search


Showing results 1 to 14 of 14
Search took 0.01 seconds. Search: Posts Made By: JaxSS
Forum: V8 - Engine, Exhaust, Bolt-Ons, Tuning Equipment 07-18-2019, 07:06 AM
Replies: 3
Views: 1,292
Posted By JaxSS
Rough idle

Rough idle
Forum: V8 - Engine, Exhaust, Bolt-Ons, Tuning Equipment 07-16-2019, 06:31 PM
Replies: 3
Views: 1,292
Posted By JaxSS
SOLD

Looking to sell:

Brand new Gwatney Performance Drop in pistons and rods.
$1350 Shipped.

Brand new JRE Blower Cam full kit with DOD delete and trunion upgrade. Everything needed for install...
Forum: Forced Induction Discussions 04-18-2019, 03:55 AM
Replies: 30
Views: 9,058
Posted By JaxSS
Thank you Trevor finally got it figured out ����

Thank you Trevor finally got it figured out ����
Forum: Forced Induction Discussions 04-16-2019, 05:38 PM
Replies: 30
Views: 9,058
Posted By JaxSS
I have the jumper harness to the pedal all...

I have the jumper harness to the pedal all plugged in and the single connector off the harness is plugged into the red wire with the matching connector coming from the boost a pump. The directions I...
Forum: Forced Induction Discussions 04-16-2019, 04:53 PM
Replies: 30
Views: 9,058
Posted By JaxSS
JMS Boost a Pump Install Question

I just installed the JMS boost a pump and it’s not activating when the throttle is depressed light just stays steady all dip switches are correctly set 5(off) 4(on) 3(on) 2(off) and 1 off after...
Forum: Forced Induction Discussions 06-05-2018, 01:38 PM
Replies: 11
Views: 3,184
Posted By JaxSS
I believe it is 17mm from the stuff I have read.

I believe it is 17mm from the stuff I have read.
Forum: Forced Induction Discussions 06-02-2018, 12:40 PM
Replies: 11
Views: 3,184
Posted By JaxSS
Thank you everyone for all the info and help. It...

Thank you everyone for all the info and help. It looks like I will have everything thing I’m going to need, now I just need the parts to get here ��. I’m surprised I haven’t seen you around jax...
Forum: Forced Induction Discussions 06-01-2018, 01:50 PM
Replies: 11
Views: 3,184
Posted By JaxSS
LT4 Fuel Upgrade Required Special Tools

Just bought the LT4 fuel upgrades for my SS and trying to find out what special tools are required to do the install. I already purchased the plug to check the cam for the high pressure pump and the...
Forum: V8 LT1 Engine, Exhaust, and Bolt-Ons 05-27-2018, 07:36 PM
Replies: 0
Views: 758
Posted By JaxSS
LT Header Codes

Did a search to try to find which codes are normal after LT header w/ off road connection pipes (all cats deleted) but didn’t find an answer. Below are the codes I currently have. Just trying to...
Forum: Forced Induction Discussions 10-09-2017, 11:32 AM
Replies: 18
Views: 4,474
Posted By JaxSS
Only reason I posted this up was to ensure no one...

Only reason I posted this up was to ensure no one would repeat this mistake in the future. All it says in the install instructions is use a big flat head or pry bar. Now everyone knows don’t use a...
Forum: Forced Induction Discussions 10-08-2017, 02:11 AM
Replies: 18
Views: 4,474
Posted By JaxSS
Well after a lot of finesseing and patience we...

Well after a lot of finesseing and patience we finally got it out with no damage and all the pieces accounted for.

https://ibb.co/c0jnDw
Forum: Forced Induction Discussions 10-07-2017, 05:24 PM
Replies: 18
Views: 4,474
Posted By JaxSS
Yea man my nerves are pretty shot. We’re still...

Yea man my nerves are pretty shot. We’re still working on it so far nothing but we have a few more tricks up our sleeve. I’m assuming if that dosent work we’re gonna have to pull the tranny to get in...
Forum: Forced Induction Discussions 10-07-2017, 01:25 AM
Replies: 18
Views: 4,474
Posted By JaxSS
That’s not going to work it’s stuck in there. ��

That’s not going to work it’s stuck in there. ��
Forum: Forced Induction Discussions 10-06-2017, 11:50 PM
Replies: 18
Views: 4,474
Posted By JaxSS
Procharger Install Problems

When we wedged the screwdriver between the torque converter bolt boss and bell housing when tightening the new crank bolt it ate the screwdriver any ideas how to get this out. Any help would be...
Showing results 1 to 14 of 14

 
Forum Jump

All times are GMT -5. The time now is 03:30 AM.

Contact Us - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com - Archive - Privacy Statement - Terms of Service / DMCA Policy - Top

Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.