Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com
 
TireRack
Go Back   Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com > Search Forums


Showing results 1 to 30 of 500
Search took 0.10 seconds.
Search: Posts Made By: CFD
Forum: Member Car Journals 04-14-2020, 06:18 PM
Replies: 1,182
Views: 131,975
Posted By CFD
Had a chance to finish off the caliper. Made an...

Had a chance to finish off the caliper. Made an adjuster mechanism and powdercoated the parts. Next chance I get I will clean up the rotor and install the caliper assembly
Forum: Member Car Journals 04-11-2020, 06:06 PM
Replies: 1,182
Views: 131,975
Posted By CFD
I've been driving the hell out of the Buick and...

I've been driving the hell out of the Buick and it's running great. The car is so light and so much different than the Camaro it's impossible to compare how the motor performs with the distributor...
Forum: Member Car Journals 04-08-2020, 06:27 PM
Replies: 1,182
Views: 131,975
Posted By CFD
I've been driving the Buick daily except when...

I've been driving the Buick daily except when raining and it's running great. I've also been picking away at the many small things I need to do. I didn't have the correct trunk bolts and it was...
Forum: Exterior Parts & Accessories 04-02-2020, 10:13 PM
Replies: 345
Views: 43,329
Posted By CFD
I am still making them

I am still making them
Forum: Member Car Journals 03-24-2020, 07:06 PM
Replies: 1,182
Views: 131,975
Posted By CFD
Finished the lid and got it installed. Next I...

Finished the lid and got it installed. Next I will work on the intake grilles but it's now functional. Before I put it on I decided to do check valve adjustment. I've put about 5 hundred miles on it...
Forum: Member Car Journals 03-23-2020, 04:58 PM
Replies: 1,182
Views: 131,975
Posted By CFD
Had a chance to check out a couple of wheel...

Had a chance to check out a couple of wheel covers. None of them had a big enough rim for my needs so I started making a lid. I cut out the piece, bead rolled the circumference to seal against the...
Forum: Member Car Journals 03-22-2020, 06:10 PM
Replies: 1,182
Views: 131,975
Posted By CFD
Finished the air cleaner to the point where I'm...

Finished the air cleaner to the point where I'm good with it for now. If I have time tomorrow I'll see if I can come up with another wheel cover, lol, in 15" and an intake hose , once I have the hose...
Forum: Member Car Journals 03-21-2020, 07:42 PM
Replies: 1,182
Views: 131,975
Posted By CFD
The lid is a Moon wheel cover, it's a 14" but I...

The lid is a Moon wheel cover, it's a 14" but I need a 15". I think it works out great and saves me the trouble of making one.

Got most of the filter assembly done. I made the inlets and tacked...
Forum: Member Car Journals 03-19-2020, 07:03 PM
Replies: 1,182
Views: 131,975
Posted By CFD
It's moving right along. Got a bit more done...

It's moving right along.

Got a bit more done with the air filter. Cut a strip for the side, ran it through the roll and welded it together, I also started cleaning up the outside welds so I can...
Forum: Member Car Journals 03-17-2020, 06:11 PM
Replies: 1,182
Views: 131,975
Posted By CFD
It's a big difference and definitely noticeable...

It's a big difference and definitely noticeable on acceleration.

I've got about 350 miles on it and it's running great. It handles very well, in fact I have to be careful because it handles well...
Forum: Member Car Journals 03-09-2020, 06:23 PM
Replies: 1,182
Views: 131,975
Posted By CFD
Been picking away at things on the Buick. The...

Been picking away at things on the Buick. The tail light lenses came in so they are now installed. We've had a couple of nice days weather wise so I've taken it out a few times, put about 100 miles...
Forum: Member Car Journals 03-05-2020, 07:05 PM
Replies: 1,182
Views: 131,975
Posted By CFD
Hi all Haven't posted much but I have been...

Hi all

Haven't posted much but I have been working on the Buick. Got all the lights wired in, finished all the wiring for the radio and back up camera and put all the glass in. I made a wood frame...
Forum: Member Car Journals 02-05-2020, 06:21 PM
Replies: 1,182
Views: 131,975
Posted By CFD
Had a chance to finish the brake rotor, got it...

Had a chance to finish the brake rotor, got it deburred, chamfered all the holes and got it installed. Sometime before mounting the caliper I will check the runout with a dial indicator, if needed it...
Forum: Member Car Journals 02-04-2020, 04:51 PM
Replies: 1,182
Views: 131,975
Posted By CFD
Thanks, they look and work great. Got the...

Thanks, they look and work great.

Got the rotor blank in and had time to machine and drill it. Tomorrow I will deburr and chamfer all the edges and holes. If I have enough time I will get it...
Forum: 5th Gen Camaro SS LS LT General Discussions 02-02-2020, 08:39 PM
Replies: 7
Views: 852
Posted By CFD
You can run an aftermarket kit to route the steam...

You can run an aftermarket kit to route the steam tube.
Forum: Member Car Journals 02-02-2020, 06:48 PM
Replies: 1,182
Views: 131,975
Posted By CFD
Hoping to have the ebrake rotor blank in the next...

Hoping to have the ebrake rotor blank in the next day or two so I've been working on glass. Got the door windows removed from the sashes, glass beaded and painted them then fitted them to the new...
Forum: Member Car Journals 01-28-2020, 05:48 PM
Replies: 1,182
Views: 131,975
Posted By CFD
The last thing needed to get an inspection...

The last thing needed to get an inspection sticker, other than the loud exhaust, lol ,is an emergency brake. I had been toying with a pinion mounted driveshaft brake so I went ahead and programmed a...
Forum: Member Car Journals 01-24-2020, 05:42 PM
Replies: 1,182
Views: 131,975
Posted By CFD
Made some progress with the Buick. I'm still in...

Made some progress with the Buick. I'm still in the early stage of recovery so I'm limited to what I can do so decided to send some time on little things needed to get an inspection sticker, I'm...
Forum: Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons 01-19-2020, 07:55 PM
Replies: 13
Views: 1,142
Posted By CFD
I use cutters from Lindy Tools.

I use cutters from Lindy Tools.
Forum: V8 - Engine, Exhaust, Bolt-Ons, Tuning Equipment 01-15-2020, 06:53 PM
Replies: 1
Views: 403
Posted By CFD
Here are a couple of quick pictures with the set...

Here are a couple of quick pictures with the set up installed
Forum: Interior Parts & Accessories 01-15-2020, 11:34 AM
Replies: 0
Views: 269
Posted By CFD
Used manual shifter knobs

Hi everyone. I'm cleaning out my shop and will be listing some items for sale.

I have two shifter knobs with stone stitching and three with IOM stitching. I am listing them as used because they...
Forum: V8 - Engine, Exhaust, Bolt-Ons, Tuning Equipment 01-15-2020, 11:28 AM
Replies: 1
Views: 403
Posted By CFD
Billet coil mounts, coil covers and coils

Hi everyone.

I'm selling some of the parts I had on my own car that I no longer can use.

This is a set of oem coils mated to a set of my billet coil mounts and covers. The coils are used, the...
Forum: Member Car Journals 01-15-2020, 11:16 AM
Replies: 1,182
Views: 131,975
Posted By CFD
Hi everyone Not much of an update because I...

Hi everyone

Not much of an update because I can't really do much and it's driving me nuts !!!! Here in MA we have been experiencing some unusually warm weather, if I could turn my friggin'...
Forum: Member Car Journals 01-08-2020, 06:11 PM
Replies: 1,182
Views: 131,975
Posted By CFD
This will most likely be the last update on the...

This will most likely be the last update on the Buick for a while, surgery is scheduled for tomorrow morning.

I had a chance to do the window channels. I couldn't come up with the same rivets used...
Forum: Member Car Journals 12-29-2019, 12:12 PM
Replies: 1,182
Views: 131,975
Posted By CFD
Playing with the Buick a little today. It's good...

Playing with the Buick a little today. It's good to know I can walk out, turn key and drive it. I'd like to get the glass in before the surgery but I'm not sure I'll have time. I have some welding to...
Forum: Member Car Journals 12-28-2019, 03:52 PM
Replies: 1,182
Views: 131,975
Posted By CFD
Got the headers and exhaust system welded,...

Got the headers and exhaust system welded, painted and installed. Needless to say it's still way too loud for a street car lol. I'll figure something out. Pulled it out of the shop and played around...
Forum: Member Car Journals 12-26-2019, 03:54 PM
Replies: 1,182
Views: 131,975
Posted By CFD
I've been busy getting my shop in order before my...

I've been busy getting my shop in order before my upcoming surgery but I have been working on the Buick. I started rebuilding the window channels, I was able to drill out the broken adjuster for the...
Forum: Member Car Journals 12-18-2019, 07:10 PM
Replies: 1,182
Views: 131,975
Posted By CFD
Thanks everyone, glad you're enjoying it. ...

Thanks everyone, glad you're enjoying it.

Got it up on the alignment rack and I couldn't be more happy. Other than a minor toe adjustment everything is right to specs . Wheel base is now 119.4 ",...
Forum: Member Car Journals 12-16-2019, 05:07 PM
Replies: 1,182
Views: 131,975
Posted By CFD
This morning I was able to get the Buick out. I...

This morning I was able to get the Buick out. I was really pressed for time so didn't get a chance to play with it or get many pictures. I did get to back it off the trailer and drive it into the...
Forum: Transmission / Driveline 12-16-2019, 04:53 PM
Replies: 376
Views: 64,948
Posted By CFD
NXTLEVL...

NXTLEVL (https://www.camaro5.com/forums/member.php?u=141905) , here's a quick picture of the shifter.
Showing results 1 to 30 of 500

 
Forum Jump

All times are GMT -5. The time now is 08:11 AM.


Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2020, vBulletin Solutions, Inc.