[BrainleSS]

Well this has been in the works for awhile now, and is finally getting close to the end. Unfortunately my health has gotten the best of me, and I'm not even doing the work myself...


Previous Set-up
LS-3.
Comp Cam 227-239 115 LSA.
PRC .650" Spring Kit / Hardend Pushrods.
Whipple Supercharger 4.0 pulley.
LG Motorsports G/5 Super Pro headers w/ high flow cats and tips.
Vmax CNC Ported Throttle Body.
Mike Norris PCV Catch Can.
SLP 160* Thermostat.
Cold-Air Inductions Intake - Black.
Pedders Ext Xa Adjust Coilovers.

731 RWHP/602 RWTQ

And the new and improved, new numbers to come!!




Engine Specifications:
CNC LSX block.
CI 427 CR – 8.8:1
Callies Crankshaft:LS1 Ultra Billet.
Callies Ultra Connecting Rods.
Diamond Pistons:Coated.
Diamond tools pins, clips & rails.
Katech Piston Squirters
ARP main/head studs.
ARP Crank Bolts.
AP series rings.
MLS Fel-pro head gaskets.
Clevite77 main bearings.
Speed pro / Clevite77 rod bearings.
Durabond LSX cam bearings.
Cloyes Extreme Hex Adjust timing set.
Melling high volume oil pump.
Comp Cams solid roller cam (27X/28X @ .050), 756"/756" , 114-deg LSA.
Comp Cams Endure – X solid lifters.
Comp Hi-Tech Pushrods.
All Pro LSW 12º-1 6 Bolt Heads w/ CNC porting 285-108-69 by Richard Reyman @ WCCH.
REV All Pro Stainless Steel Intake valve.
REV Inconel exhaust valve.
Solid Roller Dual Springs Assembly 1.550" w/damper.
Manley 10º titanium retainer. 1.550" dual spring. .740".
Manley 13152-8 10 Deg lock .311" Bead lock. Plus .050" height.
Manley 1.550" spring seats.
Jesel rocker arm kit for All Pro LSW-1.
All Pro LS7/LSW Intake.
TPIS 102 Throttle Body
All Pro valve covers
Engine Built and assembled by Billy Briggs.



Forced Induction
2 x Garrett GT3794R’s with 3” Turbo Compressor Covers.
TiaL SS light-weight 1.03 A/R Housings with 3” Outlets.
2 x TiaL Black MV-R 44mm Wastegates.
TiaL Black “Q” Blow-off Valve.
1000+ 6” Intercooler.
IPS Aluminum Intercooler Deflector Shield.
Vibrant Vacuum Manifold.
Turbowerx Exa-Pump oil Return Pump.
Thermal Heat-shield for Transmission Lines
Oil Feed & Return Line Kit featuring “Soft” Nylon Braided Hose & Black Fittings.
Sport Crimp Lines & Fittings
3” 6061 Aluminum Intercooler Tubing.
4” Powder coated 6061 Aluminum Charge-pipe.
4” Aluminum Intake Tubing w/ K&N Filters and K&N “Hydro Shields”.
Aluminum Lower Skid-plate.
AEM Windshield Washer Bottle & Accessories.
Polished Oil Cap w/oil return.


Exhaust
American Racing 1¾ Shorty headers.
3 ½ Custom Vibrant exhaust.


Injection
Aeromotive Pro Eliminator complete return style fuel system, good too 2000hp.
ATL fuel cell.
Injector dynamics 1300 injectors.
Wilson custom fuel rails.




Driveline
RPM Level 6 1800 RWHP Turbo 400 Transmission.
(With Pro Transbrake & SheetMetal Pan.)
Custom Transmission Brace w/DriveShaft Loop.
Precision Shifter (With air shift.)
SFI Flexplate and Bolts.
Setrab Transmission Oil Cooler Kit.
Drive Shaft Shop 9" Rear End kit w/ 3.89 Pro gear.
Pfadt Differential Bushings.
DSS Carbon Driveshaft w/ billet yoke.


Suspension & Chassis
NHRA Cert. 10pt. cage, w/parachute mount done by Dan @ Advanced Chassis.
Front K member done by Craig @ Extreme Innovations.
BMR 15” Wheel Conversion w/ Strange S/5090.
Strange S/2063W/ 175lb Springs.
FARKS Upper Control Arm Bushings.
Pfadt Drag Bar, Sub-frame and Other Bushings.


Miscellaneous
ProEFI Pro128 ECU.
VFN COPO Hood.
Pfadt Engine Mounts.
ATI Super Damper.
Kurt Urban Performance Water Vapor Kit
Ligenfelter Oil Cooler Block.
Setrab Engine Oil Cooler Kit.
Custom Dual Self-Emptying/Recycling Catch Cans.
Meziere WP329NElectric Water Pump.
Engine/Battery Cutoff Switch.
Remote Battery Terminals.
SJM Line Lock.
Katech Tensioner.
Power Bastard Alternator.
MSD Dynaforce Starter.