06-07-2024, 12:18 PM | #15 |
Bangshift Billy
Hey guys,
I bought a Bangshift Billy in FEB and have never installed it. Its brand new but I did open the wiring to look at it. I'll give ya a good deal if interested just message me. Thanks |
|
06-08-2024, 01:51 PM | #16 | |
Quote:
|
||
06-08-2024, 05:17 PM | #17 | |
Drives: 2014 ZL1 - M6 Join Date: Jun 2014
Location: Sylvan lake A.B. Canada
Posts: 152
|
Quote:
My current as of now is Delay 0.030 Launch slip 0.00 (found this to be usless) Ramp down 0.325 See how that works on a prep track next week. Ramp seems to be the the only real important variable.
__________________
2014 ZL1 M6 - M6, Kong X-port , Sleeved LSA 376 , Forged Bottom , LPE Ported Heads , Killer Chiller , Monster Triple Clutch , 991 RWHP, 877 RWTQ
|
|
06-09-2024, 02:27 PM | #18 | |
Quote:
No 2 step. Running slicks and leaving around 3k. I dump the clutch and it's just biting too hard and makes car fall on it's face off the hit. I thought delay down at .008 with ctap at 90% I would have a very light clutch bite. I believe ramp is only for boosted cars and was told not to worry about ramp time and have the slip at .70 |
||
06-09-2024, 02:57 PM | #19 | |
Drives: 2014 ZL1 - M6 Join Date: Jun 2014
Location: Sylvan lake A.B. Canada
Posts: 152
|
Quote:
I don’t run any slip, you need ramp down and the delay is set per car where the clutch just starts to engage the clutch
__________________
2014 ZL1 M6 - M6, Kong X-port , Sleeved LSA 376 , Forged Bottom , LPE Ported Heads , Killer Chiller , Monster Triple Clutch , 991 RWHP, 877 RWTQ
|
|
06-10-2024, 07:25 AM | #20 | |
Quote:
Well this came right from Billy. He suggested using .75 for slip and said that's about where he has it for his set up. I understand the delay and that's where I'm struggling because no matter where I put delay, the car leaves hard because it's biting too much clutch off the bat. Which at .008 I wouldn't assumed that would happen. I had an identical launch at .015. I've even been up in the .035 territory I can certainly try utilitizing the ramp down function but even Billy had in the instructions that's meant more for boosted cars that are building boost as they're leaving. |
||
06-10-2024, 07:43 AM | #21 | |
Drives: 2014 ZL1 - M6 Join Date: Jun 2014
Location: Sylvan lake A.B. Canada
Posts: 152
|
Quote:
__________________
2014 ZL1 M6 - M6, Kong X-port , Sleeved LSA 376 , Forged Bottom , LPE Ported Heads , Killer Chiller , Monster Triple Clutch , 991 RWHP, 877 RWTQ
|
|
06-10-2024, 07:47 AM | #22 |
Ya ill certainly try it. I just feel like something is going on with my delay bite. Might try turning my ctap percentage a little higher and see if that'll bring it in. Are you using stock master cylinder or no?
|
|
06-10-2024, 07:51 AM | #23 |
Drives: 2014 ZL1 - M6 Join Date: Jun 2014
Location: Sylvan lake A.B. Canada
Posts: 152
|
Yup stock master
__________________
2014 ZL1 M6 - M6, Kong X-port , Sleeved LSA 376 , Forged Bottom , LPE Ported Heads , Killer Chiller , Monster Triple Clutch , 991 RWHP, 877 RWTQ
|
|
|
Tags |
bang shift billy, clutch slippeer, drag racing, m6 racing |
|
|