My 2010 2SS/RS Build - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

bbiermanski · 06-27-2011, 01:28 AM

Well here it is, I did a lot to it before taking pictures ect.. so I'm trying to catch up now. I bought it in Dallas TX almost a year ago and installed a ADM CAI American long tube headers, hi flow cats, x pipe and Magnaflow race exhaust and a full Hotchkis suspension. Springs, strut tower brace, sway bars and sub frame connector. Once it hit 1000 miles I went to ADM and had them put in a stage 2 blower cam and springs, 160 stat, hose relocation kit and dyno tune it.

bbiermanski · 06-27-2011, 01:34 AM

Dyno run
http://www.youtube.com/user/bbierman.../0/eeSe7XLO8H0

bbiermanski · 06-27-2011, 01:54 AM

I got a little side tracked and started working on the sound system, was just going to up grade the 6X9's but it turned into a can of worms once I started. I went with Focal but then realized I needed a little more bass. So I started to build a sub box, I had a lot of issues there. It needs to be light so I built it out of glass, building a box out of MDF and putting glass on the front is easy, building the whole box out of it provided to be quite a challenge. Half way threw the build I got the great idea that you could hide a NOS bottle between the rear seat and sub box witch added to the build problems.

bbiermanski · 06-27-2011, 02:03 AM

Amp and 6X9's

SUX2BU · 06-27-2011, 02:07 AM

What heater hose kit is that? Looks really good.

bbiermanski · 06-27-2011, 07:43 PM

The hose relocation kit is from ADM Performance.

bbiermanski · 06-27-2011, 08:04 PM

Well the tire's showed up now only if they would finish building the wheel's!

bbiermanski · 07-04-2011, 09:40 PM

Well I found some time this weekend and finished the sub box. Then threw a few coats of SGM base and clear on it, (it is not quite square in the picture I set it correctly after it was wired in) The Nos bottle is also just set in there, hopefully I can finish that install next weekend.

bbiermanski · 07-04-2011, 09:48 PM

I also finished the tail light trim, bow tie black out and lens tint. I did not want issues with the police so I held back the urge and dident go to dark. For the trim and bow tie i used SEM trim black rattle can and top coated with urethane clear. With the lens I sanded them with 600 wet applied 2 thin coats of VHT night shades and top coated with urethane clear.

bbiermanski · 07-18-2011, 12:52 AM

Well I had some time this weekend and got the remote bottle opener and safety blow down installed as well as the 6 shooter short throw shifter.

bbiermanski · 08-04-2011, 11:36 PM

Finished the plumbing for the Nos, put the grill in and tinted the front side markers. I used the same method as the tail lights, the rear ones are finished just not installed yet.

2010 SSRS · 08-04-2011, 11:39 PM

looks awesome

bbiermanski · 08-05-2011, 12:43 AM

Thanks man!

MynameUS · 08-05-2011, 08:48 AM

Wow, it very nice!

06-27-2011, 01:28 AM	#1
bbiermanski Drives: 2010 2SS/RS Camaro Join Date: May 2011 Location: Seattle Wa Posts: 57	My 2010 2SS/RS Build Well here it is, I did a lot to it before taking pictures ect.. so I'm trying to catch up now. I bought it in Dallas TX almost a year ago and installed a ADM CAI American long tube headers, hi flow cats, x pipe and Magnaflow race exhaust and a full Hotchkis suspension. Springs, strut tower brace, sway bars and sub frame connector. Once it hit 1000 miles I went to ADM and had them put in a stage 2 blower cam and springs, 160 stat, hose relocation kit and dyno tune it. Attached Images

06-27-2011, 01:54 AM	#3
bbiermanski Drives: 2010 2SS/RS Camaro Join Date: May 2011 Location: Seattle Wa Posts: 57	I got a little side tracked and started working on the sound system, was just going to up grade the 6X9's but it turned into a can of worms once I started. I went with Focal but then realized I needed a little more bass. So I started to build a sub box, I had a lot of issues there. It needs to be light so I built it out of glass, building a box out of MDF and putting glass on the front is easy, building the whole box out of it provided to be quite a challenge. Half way threw the build I got the great idea that you could hide a NOS bottle between the rear seat and sub box witch added to the build problems. Attached Images

06-27-2011, 02:03 AM	#4
bbiermanski Drives: 2010 2SS/RS Camaro Join Date: May 2011 Location: Seattle Wa Posts: 57	engine bay and amp Amp and 6X9's Attached Images

06-27-2011, 02:07 AM	#5
SUX2BU Quit being a pu$$y Drives: FAST Join Date: Jan 2011 Location: Sachse TX (DFW) Posts: 5,825 View My Garage	What heater hose kit is that? Looks really good. __________________ <----- Click HERE to see ALL of my mods/write ups

06-27-2011, 08:04 PM	#7
bbiermanski Drives: 2010 2SS/RS Camaro Join Date: May 2011 Location: Seattle Wa Posts: 57	Well the tire's showed up now only if they would finish building the wheel's! Attached Images

06-27-2011, 01:34 AM	#2
bbiermanski Drives: 2010 2SS/RS Camaro Join Date: May 2011 Location: Seattle Wa Posts: 57	Dyno run http://www.youtube.com/user/bbierman.../0/eeSe7XLO8H0

06-27-2011, 07:43 PM	#6
bbiermanski Drives: 2010 2SS/RS Camaro Join Date: May 2011 Location: Seattle Wa Posts: 57	The hose relocation kit is from ADM Performance.

07-04-2011, 09:40 PM	#8
bbiermanski Drives: 2010 2SS/RS Camaro Join Date: May 2011 Location: Seattle Wa Posts: 57	Well I found some time this weekend and finished the sub box. Then threw a few coats of SGM base and clear on it, (it is not quite square in the picture I set it correctly after it was wired in) The Nos bottle is also just set in there, hopefully I can finish that install next weekend. Attached Images

07-04-2011, 09:48 PM	#9
bbiermanski Drives: 2010 2SS/RS Camaro Join Date: May 2011 Location: Seattle Wa Posts: 57	I also finished the tail light trim, bow tie black out and lens tint. I did not want issues with the police so I held back the urge and dident go to dark. For the trim and bow tie i used SEM trim black rattle can and top coated with urethane clear. With the lens I sanded them with 600 wet applied 2 thin coats of VHT night shades and top coated with urethane clear. Attached Images

07-18-2011, 12:52 AM	#10
bbiermanski Drives: 2010 2SS/RS Camaro Join Date: May 2011 Location: Seattle Wa Posts: 57	Well I had some time this weekend and got the remote bottle opener and safety blow down installed as well as the 6 shooter short throw shifter. Attached Images

08-04-2011, 11:36 PM	#11
bbiermanski Drives: 2010 2SS/RS Camaro Join Date: May 2011 Location: Seattle Wa Posts: 57	Finished the plumbing for the Nos, put the grill in and tinted the front side markers. I used the same method as the tail lights, the rear ones are finished just not installed yet. Attached Images

08-04-2011, 11:39 PM	#12
2010 SSRS Drives: 3 V8 Camaros Join Date: May 2009 Location: The Ocean State Posts: 111,186 View My Garage	looks awesome __________________ Jannetty Racing JRE Street Package

08-05-2011, 12:43 AM	#13
bbiermanski Drives: 2010 2SS/RS Camaro Join Date: May 2011 Location: Seattle Wa Posts: 57	Thanks man!

08-05-2011, 08:48 AM	#14
MynameUS Drives: camaro ss Join Date: Aug 2011 Location: VN Posts: 1	Wow, it very nice! __________________ Celebs Cars

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Latest Camaro Products - March 2010	Sean@Phastek	V8 Bolt-Ons & Tunes	26	08-04-2010 05:42 PM
MD - 2010 Camaro 2SS/RS IOM/IO 6spd- 2k Miles - Intake/Headers	FatalSports	Autos For Sale / Wanted	3	05-11-2010 09:30 AM
APF "Stage II" Turbo Build Thread \| 2010 Camaro SS!	Trevor@APF	Forced Induction - V8	1	01-19-2010 07:50 PM