***EIBACH INSTALL tomorrow***few ?'s - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

bluedevil02 · 04-09-2010, 07:30 PM

Hey guys! I recently purchased the pro-kit springs and was planning on doing the install tom. just had a few question

-Do you have to cut the bumpstops? it says no in the instructions, but Pfadt springs is a similar drop and does require it....plz clarify

-Any advice or tips are welcomed....i've done a few drops on imports i'm assuming this is pretty much the same

THANKS A BUNCH!

RedJewel2SS · 04-09-2010, 08:35 PM

you ought to, if you want the same amount of wheel travel. if you don't cut them, you might bottom out a lot easier.

BOULI306 · 04-09-2010, 08:42 PM

No, you do not have to cut the bump stops. It specifically says so in the paper that comes with the set! I have installed them and had no problems of the shocks bottoming out.
Look at the DIY section there are one or two good write-ups that i used.

D Vegas · 04-10-2010, 01:38 AM

Quote:

Originally Posted by BOULI306

No, you do not have to cut the bump stops. It specifically says so in the paper that comes with the set! I have installed them and had no problems of the shocks bottoming out.
Look at the DIY section there are one or two good write-ups that i used.

+1 dont trim bump stops. didnt do it on mine an have not had a problem. install is easy.

SoTHavok · 04-10-2010, 01:58 AM

install is easy takes about 3 hours, love the handling now its alot better

CamaroDreams07 · 04-10-2010, 02:56 AM

These things are AWESOME. I just got them put in today, tomorrow will post a full write up with pics. You will love them. Are you doing the sway bars too?

bluedevil02 · 04-11-2010, 02:27 AM

Hey guys thx for all the input! anywho install went ok except for those damn front sway endlinks arghhh..overall the ride is nice & looks sic...i only have one problem>>> after driving it around a bit its now making a clunkn/knockn sound from the front pass. side..i checkd everything to make sure it was tight...spring was seat pretty well etc..any ideas what it might be? breakn in sounds? should i get an alignment asap? thanks!

CamaroDreams07 · 04-11-2010, 02:44 AM

Quote:

Originally Posted by bluedevil02

Hey guys thx for all the input! anywho install went ok except for those damn front sway endlinks arghhh..overall the ride is nice & looks sic...i only have one problem>>> after driving it around a bit its now making a clunkn/knockn sound from the front pass. side..i checkd everything to make sure it was tight...spring was seat pretty well etc..any ideas what it might be? breakn in sounds? should i get an alignment asap? thanks!

You should have gotten an alignment ASAP. Need to do that monday morning for sure.

*TAG UR IT* · 04-11-2010, 04:03 AM

PICTURES/

SA CHEVY · 04-11-2010, 09:01 PM

Quote:

Originally Posted by TAG UR IT

PICTURES/

X2 I'm planning on doing the same kit. Also what tools did you use to install it yourself? Hoping this is something I can do on a Saturday or Sunday in the garage. Let me know, thanks.

bluedevil02 · 04-11-2010, 09:45 PM

YAY! i figured it out...was a loose bolt...anywho it rides great & looks awesome! now just need an alignment..

bluedevil02 · 04-11-2010, 09:48 PM

Quote:

Originally Posted by SA CHEVY

X2 I'm planning on doing the same kit. Also what tools did you use to install it yourself? Hoping this is something I can do on a Saturday or Sunday in the garage. Let me know, thanks.

I highly recommend doing it urself, hardest part was reinstalling endlinks...i practically did the whole install by myself aside or a few times i needed second hands....u can def do it in about 3hrs with basic hand tools...i used this link to install, couldnt have made it easier...i didnt even need a breaker bar...but i do recommend using PB blaster really helped get the bolts off..

LINK>http://www.planetlsx.com/tech/How_To...010_Camaro/131

SA CHEVY · 04-11-2010, 09:52 PM

Quote:

Originally Posted by bluedevil02

I highly recommend doing it urself, hardest part was reinstalling endlinks...i practically did the whole install by myself aside or a few times i needed second hands....u can def do it in about 3hrs with basic hand tools...i used this link to install, couldnt have made it easier...i didnt even need a breaker bar...but i do recommend using PB blaster really helped get the bolts off..

LINK>http://www.planetlsx.com/tech/How_To...010_Camaro/131

Did you end up using a coil compressor or just popping them out? I think that's the only tool I don't have handy in my arsenal anymore in the garage.

bluedevil02 · 04-11-2010, 09:59 PM

Quote:

Originally Posted by SA CHEVY

Did you end up using a coil compressor or just popping them out? I think that's the only tool I don't have handy in my arsenal anymore in the garage.

yea i rented one from AUTOZONE $50, they refund it once returned.....overall the springs arent compressed that much at all, i didn't use it when removing most of em, but you will need it when reinstalling fronts..

04-09-2010, 07:30 PM	#1
bluedevil02 Drives: 2LT/RS Join Date: Jul 2009 Location: San Antonio Posts: 844	*EIBACH INSTALL tomorrow*few ?'s Hey guys! I recently purchased the pro-kit springs and was planning on doing the install tom. just had a few question -Do you have to cut the bumpstops? it says no in the instructions, but Pfadt springs is a similar drop and does require it....plz clarify -Any advice or tips are welcomed....i've done a few drops on imports i'm assuming this is pretty much the same THANKS A BUNCH!

04-09-2010, 08:35 PM	#2
RedJewel2SS 12.23s@113mph Drives: 2SS/RS, A6, just a few bolt ons Join Date: Jul 2009 Location: Houston, TX Posts: 1,197	you ought to, if you want the same amount of wheel travel. if you don't cut them, you might bottom out a lot easier. __________________ RIP Cammie 7/15/2009 - 4/1/2011

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
DIY : Install headers on 2010 Camaro SS	Nine Ball	Camaro DIY & HOW-TO instructions & discussions	70	06-25-2020 07:40 PM
DIY : Install Performance Swaybars in 2010 Camaro	Nine Ball	Camaro DIY & HOW-TO instructions & discussions	17	09-14-2015 01:36 AM
Complete ******** install from a Novice	Susantroy1	Audio, Video, Bluetooth, Navigation, Radar, Electronics Forum	63	07-31-2015 02:25 PM
DIY : Install catback on 2010 Camaro SS	Nine Ball	Camaro DIY & HOW-TO instructions & discussions	3	08-09-2009 05:36 PM

04-09-2010, 08:42 PM	#3
BOULI306 Drives: 2011 CGM 2LT/RS black stripes Join Date: Sep 2009 Location: Tucson Posts: 137	No, you do not have to cut the bump stops. It specifically says so in the paper that comes with the set! I have installed them and had no problems of the shocks bottoming out. Look at the DIY section there are one or two good write-ups that i used.

04-10-2010, 01:58 AM	#5
SoTHavok Drives: 1 Join Date: Mar 2010 Location: 1 Posts: 610	install is easy takes about 3 hours, love the handling now its alot better

04-10-2010, 02:56 AM	#6
CamaroDreams07 Drives: Slow V6 Join Date: Jun 2009 Location: East Lansing, MI Posts: 9,361 View My Garage	These things are AWESOME. I just got them put in today, tomorrow will post a full write up with pics. You will love them. Are you doing the sway bars too?

04-11-2010, 02:27 AM	#7
bluedevil02 Drives: 2LT/RS Join Date: Jul 2009 Location: San Antonio Posts: 844	Hey guys thx for all the input! anywho install went ok except for those damn front sway endlinks arghhh..overall the ride is nice & looks sic...i only have one problem>>> after driving it around a bit its now making a clunkn/knockn sound from the front pass. side..i checkd everything to make sure it was tight...spring was seat pretty well etc..any ideas what it might be? breakn in sounds? should i get an alignment asap? thanks!

04-11-2010, 04:03 AM	#9
TAG UR IT www.Camaro5store.com Drives: 2014 ZL1 #705 Join Date: Jul 2006 Location: SA, Texas Posts: 26,544 View My Garage	PICTURES/

04-11-2010, 09:45 PM	#11
bluedevil02 Drives: 2LT/RS Join Date: Jul 2009 Location: San Antonio Posts: 844	YAY! i figured it out...was a loose bolt...anywho it rides great & looks awesome! now just need an alignment..