You are browsing camaro5 
 |
|
04-09-2015, 09:33 PM
|
#1 |
 
Drives: 2011 2SS/RS Join Date: May 2014
Location: Niagara Falls
Posts: 732
|
Underglow LED help
So I've had underglow LEDs since I first got the car last year in May and have always ran with the red because it matches the scheme of my car. Well today after my cruise I notice that my underglow is pinkish. So i thought I may have just changed the colour by mistake, but no. So everytime I switch to the "red" colour option it combines the red LEDs with blue LEDs. Anyone know why this is all of a sudden occuring?
__________________
"Scarlett" the Black Widow
BTR Stage 4 Cam, FTI 3600 Stall Converter, GM 3.91 Gears, GPI Intake Mod V2, CAI Cold Air Intake, SLP 25% Underdrive Pulley, LS3 Conversion, PRC Ported/Polished Heads, Stainless Power Long Tubes w/off-road pipes, Borla Atak Cat-Back Exhaust, Tru Cool 40K 482rwhp/425rwtq, Built and tuned by Champion Motors  |
|
|
|
04-09-2015, 09:39 PM
|
#2 |
|
HTCC Membership Director
Drives: 2013 RS Camaro Join Date: Jan 2014
Location: Cypress TX
Posts: 277
|
Hard to diagnose without knowing controller, setup, wiring runs, eyc, but I would suspect you have a short allowing power to blue. Is blue on all the time or only when red is on. Has water gotten into strips or wiring? Just have to do some troubleshooting to narrow it down
|
|
|
|
|
04-09-2015, 09:58 PM
|
#3 |
|
Drives: 2011 2SS/RS Join Date: May 2014
Location: Niagara Falls
Posts: 732
|
Well all the LED tubes are zip tied underneath the car and are daisy chained together, and the wires run up underneath the hood, through a grommet hole in the door to a control box that sits near the passengers feet, controlled by an RGB remote. When the blue option is selected the red LEDs are extremely dim but you can still see them when you look at the tubes.
__________________
"Scarlett" the Black Widow
BTR Stage 4 Cam, FTI 3600 Stall Converter, GM 3.91 Gears, GPI Intake Mod V2, CAI Cold Air Intake, SLP 25% Underdrive Pulley, LS3 Conversion, PRC Ported/Polished Heads, Stainless Power Long Tubes w/off-road pipes, Borla Atak Cat-Back Exhaust, Tru Cool 40K 482rwhp/425rwtq, Built and tuned by Champion Motors |
|
|
|
|
04-10-2015, 01:26 AM
|
#4 |
|
INFECTED
Drives: 2011 1LT Synergy Green Join Date: May 2011
Location: Upstate PA
Posts: 3,226
|
Call Led Glow, they have the best customer service .
Also where did you mount you front & rear tubes ? I'm getting ready to put in my Led Glow under body lights & grille lights . I got the 3 million color set . With 2 24 inch tubes for the upper & lower grille. I think it's going to look killer when I'm done . .
__________________
|
|
|
|
|
04-10-2015, 11:36 AM
|
#5 |
|
Drives: 2011 2SS/RS Join Date: May 2014
Location: Niagara Falls
Posts: 732
|
Yeah I think I'll have to do that. Can't remember exactly where the front tube is mounted, but the front was fairly easy. As for the rear tube I had to sort of tuck it under the diffuser because you're not supposed to have them very close to a heat source, so you have to have it a little ways away from the exhaust.
__________________
"Scarlett" the Black Widow
BTR Stage 4 Cam, FTI 3600 Stall Converter, GM 3.91 Gears, GPI Intake Mod V2, CAI Cold Air Intake, SLP 25% Underdrive Pulley, LS3 Conversion, PRC Ported/Polished Heads, Stainless Power Long Tubes w/off-road pipes, Borla Atak Cat-Back Exhaust, Tru Cool 40K 482rwhp/425rwtq, Built and tuned by Champion Motors |
|
|
|
|
04-11-2015, 10:14 PM
|
#6 |
 Drives: 2010 ss1 black Join Date: Mar 2014
Location: United States
Posts: 6
|
My front strip was installed just behind the air dam.
Typically I will install items like this myself but my wife surprised me with my LEDs already installed. Unfortunately the installer decided that double sided tape would be sufficient. Well either it wasn't or he didn't prep it correctly because I pulled in my driveway today and noticed my front strip sitting in the street. I plan on either using zip ties or cable clamps to reinstall. |
|
|
|
|
04-12-2015, 12:03 AM
|
#7 |
|
Drives: 2011 2SS/RS Join Date: May 2014
Location: Niagara Falls
Posts: 732
|
Zip ties all the way. 3M tape is strong, but considering it's underneath the car I went with zip ties. Plus there were some holes underneath that were prefect for the zip ties to go through.
__________________
"Scarlett" the Black Widow
BTR Stage 4 Cam, FTI 3600 Stall Converter, GM 3.91 Gears, GPI Intake Mod V2, CAI Cold Air Intake, SLP 25% Underdrive Pulley, LS3 Conversion, PRC Ported/Polished Heads, Stainless Power Long Tubes w/off-road pipes, Borla Atak Cat-Back Exhaust, Tru Cool 40K 482rwhp/425rwtq, Built and tuned by Champion Motors |
|
|
|
|
04-12-2015, 12:10 AM
|
#8 |
|
INFECTED
Drives: 2011 1LT Synergy Green Join Date: May 2011
Location: Upstate PA
Posts: 3,226
|
Thanks , I looking at in front of the air dam . Using pipe brackets , and push pins , with tie straps and running the wire in loom. . I'm hoping to full the front end off tomorrow and install the 2 grill tubes . Wish me luck ..
__________________
|
|
|
|
|
04-12-2015, 04:12 PM
|
#9 |
|
KNGTFALL
Drives: 2012 2SS 45th edition Join Date: Aug 2012
Location: (Near) Charlotte, NC
Posts: 1,533
|
Bio can you take a picture of the LED strip (near the LEDs) I have an idea for a project but need to see the Type or circuit it has.
|
|
|
|
|
04-14-2015, 08:02 PM
|
#10 |
|
INFECTED
Drives: 2011 1LT Synergy Green Join Date: May 2011
Location: Upstate PA
Posts: 3,226
|
Here's pics, 45th
__________________
|
|
|
|
|
04-14-2015, 08:09 PM
|
#11 |
|
KNGTFALL
Drives: 2012 2SS 45th edition Join Date: Aug 2012
Location: (Near) Charlotte, NC
Posts: 1,533
|
Thanks, That's good enough for what I need.
|
|
|
|
|
|
|
|
 |
|
|
