ZL1 bumper grill piece??? - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

seanjhon · 12-10-2013, 11:52 AM

Hello Everyone,

So i seached everywhere and cannot figure out what this piece attaches to. I recently purchased the zl1 grill and this was one of the pieces that came with it that I had to order. Where exactly where this go. The bumper is currently in the shop getting painted so I cant play around with it.

I was also reading that we have to drill holes in certain spots. Where exactly do we drill, is there a picture out there somewhere that I can reference?

Last question...I plan on doing this myself (install) and want to know does anyone have a picture of where I place the jack stands once I lift up to get the front elevated so I can take the tires off and all that? I seen the diagram with the points on the camaro laying on the side and see those points but is the places different if you place the jacks stands in front of the car?

el ess A · 12-10-2013, 12:03 PM

That's the stiffener piece that goes behind the lower section of the bumper fascia between the upper and lower grill. It will become very obvious where it goes when you get your fascia back. IIRC, it just snaps into place.

OHIO SPEED · 12-10-2013, 12:06 PM

energy absorber #20

seanjhon · 12-10-2013, 12:51 PM

Thanks everyone for the respnses

seanjhon · 12-10-2013, 12:59 PM

anyone have any pics or explanations of the jack stand positions to lift the front of car up in front?

Visago · 12-10-2013, 01:14 PM

Quote:

Originally Posted by seanjhon

anyone have any pics or explanations of the jack stand positions to lift the front of car up in front?

http://www.camaro5.com/forums/showth...ht=jack+points

seanjhon · 12-11-2013, 02:29 PM

Does anyone know where the new hole in the wheel well liner needs to be drilled? Any Pics?

12-10-2013, 11:52 AM	#1
seanjhon Drives: 2013 camaro Join Date: Mar 2013 Location: Colorado Posts: 607	ZL1 bumper grill piece??? Hello Everyone, So i seached everywhere and cannot figure out what this piece attaches to. I recently purchased the zl1 grill and this was one of the pieces that came with it that I had to order. Where exactly where this go. The bumper is currently in the shop getting painted so I cant play around with it. I was also reading that we have to drill holes in certain spots. Where exactly do we drill, is there a picture out there somewhere that I can reference? Last question...I plan on doing this myself (install) and want to know does anyone have a picture of where I place the jack stands once I lift up to get the front elevated so I can take the tires off and all that? I seen the diagram with the points on the camaro laying on the side and see those points but is the places different if you place the jacks stands in front of the car? Attached Images

12-10-2013, 12:06 PM	#3
OHIO SPEED Drives: 2010 1LT v6 Twin Turbo Join Date: Jun 2010 Location: Northeast Ohio Posts: 5,829 View My Garage	part? energy absorber #20 Attached Images

12-10-2013, 12:03 PM	#2
el ess A Older Than Dirt Drives: 2010 & 2013 Camaros Join Date: Apr 2010 Location: Aiken, SC Posts: 4,678	That's the stiffener piece that goes behind the lower section of the bumper fascia between the upper and lower grill. It will become very obvious where it goes when you get your fascia back. IIRC, it just snaps into place. __________________ 2010 2SS TE, 1 of 822/2013 Camaro ZL1 vert, 1 of 54

12-10-2013, 12:51 PM	#4
seanjhon Drives: 2013 camaro Join Date: Mar 2013 Location: Colorado Posts: 607	Thanks everyone for the respnses

12-10-2013, 12:59 PM	#5
seanjhon Drives: 2013 camaro Join Date: Mar 2013 Location: Colorado Posts: 607	anyone have any pics or explanations of the jack stand positions to lift the front of car up in front?

12-11-2013, 02:29 PM	#7
seanjhon Drives: 2013 camaro Join Date: Mar 2013 Location: Colorado Posts: 607	Does anyone know where the new hole in the wheel well liner needs to be drilled? Any Pics?