You are browsing camaro5 
 |
|
12-11-2014, 03:46 PM
|
#1 |
 Drives: 2013 ZL1 White/Carbon fiber Vin#658 Join Date: Oct 2013
Location: Yakima Wa
Posts: 63
|
Snout rebuild?
Does anyone know who can rebuild a 2013 ZL1 Snout? Bearings,shaft, ect?
Last edited by Buckstadler; 12-11-2014 at 03:46 PM. Reason: Nore info |
|
|
|
12-11-2014, 03:47 PM
|
#2 |
|
Drives: 2013 ZL1 White/Carbon fiber Vin#658 Join Date: Oct 2013
Location: Yakima Wa
Posts: 63
|
ASAP?
|
|
|
|
|
12-11-2014, 07:25 PM
|
#3 |
|
Speed Freak
Drives: 2013 ZL1 Camaro, 2016 Camaro SS Join Date: Jun 2013
Location: Ardmore, OK
Posts: 2,637
|
You might call Andy at ADM Performance. He can do it if he doesn't have too much other work lined up. He stays pretty busy.
__________________
2016 SS -AGP twin Borg Warner 7163 EFR's, LT4 mechanical pump, LT4 injectors, Walbro 255 low side, Castrol SRF. 734whp/759 tq
2013 ZL1 -ADM - 427 LSX 6 bolt, O-ringed block built by LME. Twin PT6466 turbos. RPM custom manual trans, RPS Quad carbon clutch, 9" Hendrix rear diff & axles. ADM/squash fuel system, Ron Davis radiator, Spal fans, AGP air to air, turbo plumbing. LPE oil cooler, rear bushing upgrade, roll bar...etc. rwhp 1400+... 212.5mph, best Texas mile to date.  |
|
|
|
|
12-11-2014, 08:44 PM
|
#4 |
|
Going for Plaid
Drives: 2011 C6 Join Date: Jan 2010
Location: Phoenix
Posts: 885
|
Cordes might have a used one on the shelf.
__________________
2014 ZL1, manual trans, carbon hood insert, Rotofab, Pacesetter 1 7/8" headers, 1" drop BMR springs, stock pulleys, 91 octane tune, 545rwhp & 515rwtq
Serviced and modded by Cordes Performance. 2011 C6, 750rwhp, forged LS3, ported LSA heads, Vortech Ti-trim, 227/243 115+4 Lunati cam, ported LS3 intake, Alky Control methanol, Pfadt sways/shocks/trans mounts, Pfadt tri-y headers(Sold 6/28/14) |
|
|
|
|
12-11-2014, 09:01 PM
|
#5 |
|
Drives: 2013 ZL1 White/Carbon fiber Vin#658 Join Date: Oct 2013
Location: Yakima Wa
Posts: 63
|
Could you PM me Cordes phone #?
|
|
|
|
|
12-11-2014, 09:09 PM
|
#6 |
|
Drives: 2013 ZL1 White/Carbon fiber Vin#658 Join Date: Oct 2013
Location: Yakima Wa
Posts: 63
|
I'll call ADM. In the morning. I think upper pulley installation damaged to the bearings��!
|
|
|
|
|
12-12-2014, 01:16 PM
|
#7 | |
 
Drives: BLUE CAMARO ZL1 1LE M6 Join Date: Jun 2009
Location: ON THE DYNO WATERBURY CT.
Posts: 15,410
|
Quote:
__________________
www.jannettyracing.com
Celebrating 39 years Performance parts, Installation, Fabrication, Dyno tuning, Remote custom tuning, and alignments. 203-753-7223 Waterbury CT. 06705 email tedj@jannettyracing.com |
|
|
|
|
12-12-2014, 05:52 PM
|
#8 |
|
Drives: 2013 ZL1 White/Carbon fiber Vin#658 Join Date: Oct 2013
Location: Yakima Wa
Posts: 63
|
I called them yesterday. They don't have the parts in stock. I'm running into a lot road blocks on the parts. Couldn't a guy match up the bearings with a better set.
|
|
|
|
|
|
|
|
 |
|
|
