LED Grill Lightning - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

YoungMulaBaby · 06-04-2015, 10:41 PM

I was thinking of getting the Purple LED Color for my Camaro. But I need a proper switch to turn it on/off. I was thinking either bringing the wires in to the interior and plug it into one of the emblem pro's switchplate rocker switches that I'm getting.. or find a wireless controller and control the light on/off from that. Also, where can I get a wireless controller for a good cheap price?
From the two, what would be a more elegant choice?

opossum · 06-05-2015, 03:40 AM

Hallo,

this is a wireless Switch. http://www.ebay.de/itm/301632476412?...%3AMEBIDX%3AIT . You can install the receiver complet in the engine compartment. It needs +12V, and has two channels. I have installed it and switching the led-stripes under my splitter wireless from over 50 meters.

best regards from Germany
opossum

opossum · 06-17-2015, 04:43 AM

Hallo,

here are the pictures. I have built a little baseplate of sheet steel. Then i have installed the remote control receiver on this plate. The groundcable i have connected on the srew behind the air filter (cable shoes soldered).
Then you can see, wich lights i switch with this remote control.

Best regards from Germany
opoSSum

06-04-2015, 10:41 PM	#1
YoungMulaBaby Drives: Camaro 2014 2LT Join Date: May 2014 Location: Georgia Posts: 68	LED Grill Lightning I was thinking of getting the Purple LED Color for my Camaro. But I need a proper switch to turn it on/off. I was thinking either bringing the wires in to the interior and plug it into one of the emblem pro's switchplate rocker switches that I'm getting.. or find a wireless controller and control the light on/off from that. Also, where can I get a wireless controller for a good cheap price? From the two, what would be a more elegant choice? Last edited by YoungMulaBaby; 06-04-2015 at 11:54 PM.

06-05-2015, 03:40 AM	#2
opossum Drives: 2013 Join Date: Dec 2013 Location: Germany Blankenhagen Posts: 81	Hallo, this is a wireless Switch. http://www.ebay.de/itm/301632476412?...%3AMEBIDX%3AIT . You can install the receiver complet in the engine compartment. It needs +12V, and has two channels. I have installed it and switching the led-stripes under my splitter wireless from over 50 meters. best regards from Germany opossum __________________ Chevrolet Camaro - V8 - MT - 2013 - European Version - Inferno Orange/ Inferno orange - ACC Sidemarker ghosted - Dash Kit PAC RPK5-GM4101 with DNX8170DABS - Amp KAC-8406 - Sub Pioneer TS-WX110A - Rear- and Front-Camera - ACC Mail Slot Scanner RGB - Pedders Sportsryder - painted parts in engine compartment - black powder coated original rims - H & R wheel plates 20mm front and rear axle - 1 LE steering wheel - MGW Short shifter replacement - aluminum door Pins - ACS T4 Splitter - us-mirrors - ZL1 side rockers - High Wing Spoiler

06-17-2015, 04:43 AM	#3
opossum Drives: 2013 Join Date: Dec 2013 Location: Germany Blankenhagen Posts: 81	Hallo, here are the pictures. I have built a little baseplate of sheet steel. Then i have installed the remote control receiver on this plate. The groundcable i have connected on the srew behind the air filter (cable shoes soldered). Then you can see, wich lights i switch with this remote control. Best regards from Germany opoSSum Attached Images __________________ Chevrolet Camaro - V8 - MT - 2013 - European Version - Inferno Orange/ Inferno orange - ACC Sidemarker ghosted - Dash Kit PAC RPK5-GM4101 with DNX8170DABS - Amp KAC-8406 - Sub Pioneer TS-WX110A - Rear- and Front-Camera - ACC Mail Slot Scanner RGB - Pedders Sportsryder - painted parts in engine compartment - black powder coated original rims - H & R wheel plates 20mm front and rear axle - 1 LE steering wheel - MGW Short shifter replacement - aluminum door Pins - ACS T4 Splitter - us-mirrors - ZL1 side rockers - High Wing Spoiler