JMS BAP Help - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

todmich · 01-28-2018, 01:13 PM

Hello all,

This weekend I have been installing new injectors and some other things from Jennetty now come the time for the JMS BAP this one has me a little nervous. Everything seems as if it should be simple, I have located the fuse I need to swap to a 30 but the fuel control module isn't in the trunk. Can someone point me in the correct direction? Is it on the passenger side back seat area?

My second question is I have the plug and play version of the JMS from Jennetty is the pedal connection right above the pedals in the foot well or do I need to remove panels to get to this also?

Thank you all for the help.

todmich · 01-28-2018, 01:41 PM

Ok I found the module, I was over looking it. What wire do I cut to splice, is it the red wire with the black stripe?

ABADZL1 · 01-28-2018, 01:48 PM

The wiring you need access to is located in the trunk at the fuse panel there. You do not have to go further forward to the actual module.

todmich · 01-28-2018, 03:14 PM

Thank you, I will look there at the fuse block. Will this be a heavy gauge wire? It is red and white correct?

Thanks

ABADZL1 · 01-28-2018, 03:20 PM

Quote:

Originally Posted by todmich

Thank you, I will look there at the fuse block. Will this be a heavy gauge wire? It is red and white correct?

Thanks

They are heavy. One is red. Don't remember if both are or one is white.

ZMEnow · 01-28-2018, 04:00 PM

Use this thread... As you disconnect the terminal block the upper peg should have 12 volts, the lower peg is where you are injecting the 14 volts back in to the FPCM. I did not cut mine and has work well on the most severe track days with 100's of laps. I did place a plastic tie to keep the terminal secure.

http://www.camaro5.com/forums/showth...ht=JMS+install

todmich · 01-28-2018, 04:13 PM

Thank you very much, this helps. I got this install now.

ABADZL1 · 01-28-2018, 06:43 PM

These settings will be a good starter for you.

todmich · 01-28-2018, 09:25 PM

Sweet, thank you guys. I was nervous about tackling this one but you all made it easy.

01-28-2018, 01:13 PM	#1
todmich Drives: 2013 Camaro ZL1 Join Date: Jan 2018 Location: Corpus Christi Posts: 5	JMS BAP Help Hello all, This weekend I have been installing new injectors and some other things from Jennetty now come the time for the JMS BAP this one has me a little nervous. Everything seems as if it should be simple, I have located the fuse I need to swap to a 30 but the fuel control module isn't in the trunk. Can someone point me in the correct direction? Is it on the passenger side back seat area? My second question is I have the plug and play version of the JMS from Jennetty is the pedal connection right above the pedals in the foot well or do I need to remove panels to get to this also? Thank you all for the help.

01-28-2018, 01:48 PM	#3
ABADZL1 ZL1 Pilot Drives: 2013 ZL1 Join Date: Apr 2014 Location: TN Posts: 1,673 View My Garage	The wiring you need access to is located in the trunk at the fuse panel there. You do not have to go further forward to the actual module. __________________

01-28-2018, 04:00 PM	#6
ZMEnow Drives: ZL1, 2013, tri-coat-red, manual Join Date: Nov 2013 Location: Michigan Posts: 1,665	Use this thread... As you disconnect the terminal block the upper peg should have 12 volts, the lower peg is where you are injecting the 14 volts back in to the FPCM. I did not cut mine and has work well on the most severe track days with 100's of laps. I did place a plastic tie to keep the terminal secure. http://www.camaro5.com/forums/showth...ht=JMS+install Attached Images

01-28-2018, 06:43 PM	#8
ABADZL1 ZL1 Pilot Drives: 2013 ZL1 Join Date: Apr 2014 Location: TN Posts: 1,673 View My Garage	These settings will be a good starter for you. __________________

01-28-2018, 01:41 PM	#2
todmich Drives: 2013 Camaro ZL1 Join Date: Jan 2018 Location: Corpus Christi Posts: 5	Ok I found the module, I was over looking it. What wire do I cut to splice, is it the red wire with the black stripe?

01-28-2018, 03:14 PM	#4
todmich Drives: 2013 Camaro ZL1 Join Date: Jan 2018 Location: Corpus Christi Posts: 5	Thank you, I will look there at the fuse block. Will this be a heavy gauge wire? It is red and white correct? Thanks

01-28-2018, 04:13 PM	#7
todmich Drives: 2013 Camaro ZL1 Join Date: Jan 2018 Location: Corpus Christi Posts: 5	Thank you very much, this helps. I got this install now.

01-28-2018, 09:25 PM	#9
todmich Drives: 2013 Camaro ZL1 Join Date: Jan 2018 Location: Corpus Christi Posts: 5	Sweet, thank you guys. I was nervous about tackling this one but you all made it easy.