You are browsing camaro5 
 |
|
06-25-2018, 11:21 PM
|
#1 |
 
|
help, car wont fire.
i just did a whipple and cam install on my ‘10 ls3. its getting fuel, plugs are wet and i couldnt get spark. i did a zr1 map sensor and new injectors. car will turn over but will not fire. the cars previous tune was for a cam,lt, intake, nitrous setup. will this play into it or should the car atleast try to fire?
|
|
|
|
06-25-2018, 11:22 PM
|
#2 |
|
|
and i have all granetelli plugs and coils if that makes a difference.
|
|
|
|
|
06-26-2018, 01:20 AM
|
#3 |
    
|
I would check all ignition wiring plugs, then the cam sensor, if you can't get any spark at all, this is just where i would start i am far from a mechanic though good luck hope its something simple
__________________
Cai intake and a few other mods😎
 |
|
|
|
|
06-26-2018, 05:35 AM
|
#4 |
|
|
is their any ground straps from chassis to car?
|
|
|
|
|
06-26-2018, 06:09 AM
|
#5 |
|
|
ik theirs wiring harness grounds but i know i didnt ground the block to the chassis
|
|
|
|
|
06-26-2018, 07:34 AM
|
#6 | |
  Drives: 2011 Camaro SS 6sp Join Date: Nov 2016
Location: Drivers Seat
Posts: 1,905
|
Quote:
I wouldnt even try to start it without that.
__________________
2011 Camaro SS---SOLD
TMS Dart 427 FED M311s, ESS Tuning G4 Blower, DSX Triple FP Assembly, DSX FF, FIC1300, Mcleod RXT 1200HD, Edlebrock Pro Flo XT 1158whp 1017wtq. 2010 CTS-V A6 - "Stock" SOLD 630whp 658wtq 2024 F-150 RCSB 5.0 4x4 waiting for tunes... |
|
|
|
|
|
06-26-2018, 10:04 AM
|
#7 |
|
|
https://www.camaro5.com/forums/showthread.php?t=221700
Look at blakes post, I really dont believe it would be a ground in that area
__________________
Cai intake and a few other mods😎
|
|
|
|
|
06-26-2018, 10:12 AM
|
#8 |
|
|
https://www.camaro5.com/forums/showthread.php?t=125123
Here is a article you can go over your step to see if you skipped one, even shows timing dot lineup between crank and cam
__________________
Cai intake and a few other mods😎
|
|
|
|
|
06-26-2018, 06:27 PM
|
#9 |
|
|
i bonded all the grounds to the block, but i never bonded the block to the chassis. i only turned it over a few times to see if it would fire. spark plugs are wet. ive done a few cam swaps. i just find it odd i dont have spark. its getting a startup tune thursday. so if it doesnt start after that����*♂️
|
|
|
|
|
06-27-2018, 04:52 PM
|
#10 |
|
Drives: 2011 Camaro SS 6sp Join Date: Nov 2016
Location: Drivers Seat
Posts: 1,905
|
Is it throwing any codes?
__________________
2011 Camaro SS---SOLD
TMS Dart 427 FED M311s, ESS Tuning G4 Blower, DSX Triple FP Assembly, DSX FF, FIC1300, Mcleod RXT 1200HD, Edlebrock Pro Flo XT 1158whp 1017wtq. 2010 CTS-V A6 - "Stock" SOLD 630whp 658wtq 2024 F-150 RCSB 5.0 4x4 waiting for tunes... |
|
|
|
|
06-27-2018, 05:19 PM
|
#11 |
Drives: 2010 Camaro SS Join Date: Jan 2015
Location: Valencia
Posts: 1,305
|
did you update the tune with the new map offset?
|
|
|
|
|
06-27-2018, 10:20 PM
|
#12 |
 Drives: 2010 ss Join Date: Oct 2015
Location: windom mn
Posts: 337
|
car will not start with a different map sensor.i had the same problem,put the stock one in.
|
|
|
|
|
07-01-2018, 04:12 PM
|
#13 |
|
|
i went threw everything and found that theirs 2 grounds the connect to the back of the heads werents connected. hooked them up amd she fired right up
|
|
|
|
|
07-02-2018, 09:45 AM
|
#14 |
Drives: 2010 2SS/Black Join Date: Mar 2009
Location: Tucson, AZ
Posts: 608
|
I had the same issue on my 2010 SS after a Manguson SC install. Turned out with my year Camaro didn't have the SC tables to support the SC. The ECM had s down level program, took it to the dealer to have the current FW uploaded. Started right up after wards. Not sure it's your issue but it can affect the early Camaro shipments.
__________________
2010 Black 2SS L99
Mods: * CAI Intake * Magnuson MP2300 TVS Supercharger/RDS Spacer * Vector Motorsports Tune * Stainless Power LT/Hi Flow Cats/Tru X-* Pipe/36" J-Pipes/40 Series * R1 Concepts ceramic pads and slotted/drilled rotors |
|
|
|
|
|
|
|
 |
|
|
