Square tire with Z28 rims help please - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

jaysrippen · 05-26-2022, 02:21 PM

Good day guys, I ALWAYS wanted the Z28 replica rims for my 2010 SS and would finally like to order a set of replica OE Creations Wheels PR126 Matte Black. I run 285/35-20 all around and was wondering which offset on the 10" wide rims would NOT RUB, or have more clearance from rubbing.
Theres 2 to pick from in the 10" wide, a ET23 offset and a ET35 offset.
Suggestions please?

Excited

gtstorey · 05-26-2022, 02:26 PM

https://tiresize.com/wheel-offset-calculator/

https://www.oponeo.co.uk/blog/wheel-...fset-explained
"When the ET value decreases, the alloy wheels will protrude further out."

jaysrippen · 05-26-2022, 02:30 PM

with my square 285/35 20 and all 10" wide rims its alot different then comparing factory offset. So thought id see if anyone has advise? thanks again

gtstorey · 05-26-2022, 02:57 PM

"or have more clearance from rubbing.
Theres 2 to pick from in the 10" wide, a ET23 offset and a ET35 offset."

So of the two to choose from ET23 would have more clearance by 0.47".

SS Performance · 05-26-2022, 06:37 PM

https://www.camaro5.com/forums/showthread.php?t=314778

That thread is about 1LE's. Stock front wheels are 10"wide with a 23 offset. You would need to figure out the rear.

05-26-2022, 02:21 PM	#1
jaysrippen Drives: 2010ss M6 LS3 Join Date: Jun 2018 Location: Alberta Canafa Posts: 38	Square tire with Z28 rims help please Good day guys, I ALWAYS wanted the Z28 replica rims for my 2010 SS and would finally like to order a set of replica OE Creations Wheels PR126 Matte Black. I run 285/35-20 all around and was wondering which offset on the 10" wide rims would NOT RUB, or have more clearance from rubbing. Theres 2 to pick from in the 10" wide, a ET23 offset and a ET35 offset. Suggestions please? Excited __________________ 2010 SS M6, stage 2 summit cam, CAI Intake/long tube cat delete with flow master/ZEX NOS at 150RWHP/ custom tune/MSD wires/short throw shifter/ crank vent catchcan/ SS braided brake lines/ 1.5” lower springs/bigger rear sway bar/fully poly bushings everywhere/toe arms/trail arms/front caster plates/factory shocks/steering poly inserts

05-26-2022, 02:30 PM	#3
jaysrippen Drives: 2010ss M6 LS3 Join Date: Jun 2018 Location: Alberta Canafa Posts: 38	with my square 285/35 20 and all 10" wide rims its alot different then comparing factory offset. So thought id see if anyone has advise? thanks again __________________ 2010 SS M6, stage 2 summit cam, CAI Intake/long tube cat delete with flow master/ZEX NOS at 150RWHP/ custom tune/MSD wires/short throw shifter/ crank vent catchcan/ SS braided brake lines/ 1.5” lower springs/bigger rear sway bar/fully poly bushings everywhere/toe arms/trail arms/front caster plates/factory shocks/steering poly inserts

05-26-2022, 06:37 PM	#5
SS Performance Drives: 02 Camaro B4C Join Date: Nov 2016 Location: Cape May County NJ Posts: 749	https://www.camaro5.com/forums/showthread.php?t=314778 That thread is about 1LE's. Stock front wheels are 10"wide with a 23 offset. You would need to figure out the rear. __________________ A man's garage is his castle 1969 Camaro SS 1970 Camaro SS 2002 Camaro B4C 2014 Camaro SS Dedicated Track Car 2015 Camaro 1SS 1LE 2008 HHR SS 1996 Silverado Crew Cab Long Bed Dual Rear Wheel

05-26-2022, 02:26 PM	#2
gtstorey Drives: 2010 Camaro SS2,L99, LSA SC Join Date: Aug 2017 Location: Huntsville, AL Posts: 2,450	https://tiresize.com/wheel-offset-calculator/ https://www.oponeo.co.uk/blog/wheel-...fset-explained "When the ET value decreases, the alloy wheels will protrude further out."

05-26-2022, 02:57 PM	#4
gtstorey Drives: 2010 Camaro SS2,L99, LSA SC Join Date: Aug 2017 Location: Huntsville, AL Posts: 2,450	"or have more clearance from rubbing. Theres 2 to pick from in the 10" wide, a ET23 offset and a ET35 offset." So of the two to choose from ET23 would have more clearance by 0.47".