Will this clutch work ? - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

RGC1 · 06-26-2025, 07:53 AM

Just wondering if anybody can tell me will the dual disc clutch from GM for ls/lsa. Work in my 2014 ls3 ?
Also would it use the same throw out bearing ?
Or should l just go centreforce or McLeod ?
So far I’m not running any power adders
Thanks, new to fifth gen

CamaroCracka · 06-26-2025, 08:07 AM

LSA clutch won't work because LSA crank is 8 bolt so LSA flywheel is different than LS flywheel. I believe throwout bearings are the same, but not certain on that. McLeod, Monster etc. are probably a better choice.

Pops · 06-26-2025, 08:07 AM

I like the Mcleod RST

CamaroDreams76 · 06-26-2025, 07:19 PM

No as stated its a different flywheel. Years ago a pretty prominent member ran a centerforce dyad clutch on his twin turbo camaro and basically it burnt up immediately and couldn't handle the power even though it was well rated for it. Also he complained about the clutches engagement. Then when he tried to warranty it, centerforce basically told him the clutch burning up was his fault and denied the claim. So I say pass on them.

I have a McLeod RXT in my car. Its pretty good. Takes some getting used to because of the need for more throttle input when taking off from a stock but overall its super smooth. I would recommend the RST which is a much more street friendly clutch. That is if you dont want to surpass the 700/800whp range.

Stock throwout bearings are fine with aftermarket clutches. Monster has their own upgraded stock bearing.

RGC1 · 06-26-2025, 08:20 PM

Thanks guys for the information, very much appreciated McLeod it is , thx

06-26-2025, 07:53 AM	#1
RGC1 Drives: 2014 SS Camaro Join Date: Jun 2025 Location: Canada Posts: 9	Will this clutch work ? Just wondering if anybody can tell me will the dual disc clutch from GM for ls/lsa. Work in my 2014 ls3 ? Also would it use the same throw out bearing ? Or should l just go centreforce or McLeod ? So far I’m not running any power adders Thanks, new to fifth gen

06-26-2025, 08:07 AM	#2
CamaroCracka Drives: 2010 Turbo LS3 Join Date: Dec 2009 Location: Palm Bay, FL Posts: 3,065	LSA clutch won't work because LSA crank is 8 bolt so LSA flywheel is different than LS flywheel. I believe throwout bearings are the same, but not certain on that. McLeod, Monster etc. are probably a better choice. __________________ 2010 SS - Kind of an On3 kit, CTR 78/80, CompCam 239/251 620/632 122+4, E85, Z28 suspension and ZL1 diff with Outlaw axles. Gen6 ZL1 brakes. 2011 Vert - 416/w 230/236 .612/.602 115lsa, 1LE suspension w/32mm rear bar. Z28 diff. Gen6 ZL1 brakes.

06-26-2025, 07:19 PM	#4
CamaroDreams76 Tri-County Camaro SWFL Drives: 2013 IOM 2SS/RS/1LE Join Date: Apr 2013 Location: South West FL Posts: 3,580 View My Garage	No as stated its a different flywheel. Years ago a pretty prominent member ran a centerforce dyad clutch on his twin turbo camaro and basically it burnt up immediately and couldn't handle the power even though it was well rated for it. Also he complained about the clutches engagement. Then when he tried to warranty it, centerforce basically told him the clutch burning up was his fault and denied the claim. So I say pass on them. I have a McLeod RXT in my car. Its pretty good. Takes some getting used to because of the need for more throttle input when taking off from a stock but overall its super smooth. I would recommend the RST which is a much more street friendly clutch. That is if you dont want to surpass the 700/800whp range. Stock throwout bearings are fine with aftermarket clutches. Monster has their own upgraded stock bearing. __________________ Just bolt ons........ https://www.camaro5.com/forums/showthread.php?t=343023

06-26-2025, 08:07 AM	#3
Pops Drives: 2010 Camaro SS2 2012 C6 vette M6 Join Date: Jan 2022 Location: Atlanta Ga Posts: 85	I like the Mcleod RST

06-26-2025, 08:20 PM	#5
RGC1 Drives: 2014 SS Camaro Join Date: Jun 2025 Location: Canada Posts: 9	Thanks guys for the information, very much appreciated McLeod it is , thx