You are browsing camaro5 
 |
|
08-13-2011, 10:18 AM
|
#15 |
       
|
Thank you the glue is letting up a little from the heat but its nothing to bad no1 else notices it..except me
__________________
 |
|
|
|
08-14-2011, 08:56 AM
|
#16 |
 
Drives: Victory Redhead Join Date: Jun 2010
Location: Chicago
Posts: 111
|
thanks for the info, advise and tips
|
|
|
|
|
08-14-2011, 11:12 AM
|
#17 |
|
|
if you want to know anything else about what i did just pm me or write in my members journal(click on my sig) hard to remember to keep checking back here
__________________
|
|
|
|
|
08-14-2011, 12:22 PM
|
#18 |
Drives: White M6 1LT RS Join Date: Mar 2010
Location: Canton, MI
Posts: 1,676
|
I just did what the OP is talking about doing. It cost me 12 dollars in rattle cans. Rustoleum for Plastic and Rustoleum Clear for Plastic. I took the panels off and tore off the cloth. Cleaned them and started painting them.
  
__________________
Pfadt Sway Bars - FE3 Suspension - Barton Shifter - IdealG's Clutch Master Cylinder - Trifecta - Vmax TB - Vararam Intake - MACE 25mm Insulator - Plenum Insulator - Ported/Gasket Matched Intake Manifold - Rx Catchcan - AAC DRL's - 4 Pack Aux Gauges - Steering Controls - AAC Afterburners - DIY Led Sidemarkers - ZL1 Front End
Next mod: Done! |
|
|
|
|
08-14-2011, 12:24 PM
|
#19 | |
|
|
Quote:
__________________
|
|
|
|
|
|
08-14-2011, 12:26 PM
|
#20 | |
|
Drives: White M6 1LT RS Join Date: Mar 2010
Location: Canton, MI
Posts: 1,676
|
Quote:
Yeah I'm lucky I had white. Once the clear dries fully. I will wet sand the clear and polish and wax the panels.
__________________
Pfadt Sway Bars - FE3 Suspension - Barton Shifter - IdealG's Clutch Master Cylinder - Trifecta - Vmax TB - Vararam Intake - MACE 25mm Insulator - Plenum Insulator - Ported/Gasket Matched Intake Manifold - Rx Catchcan - AAC DRL's - 4 Pack Aux Gauges - Steering Controls - AAC Afterburners - DIY Led Sidemarkers - ZL1 Front End
Next mod: Done! |
|
|
|
|
|
08-14-2011, 09:01 PM
|
#21 |
 |
MACH that looks great. Looks like I will start looking into doing this project. Thanks
__________________
|
|
|
|
|
08-15-2011, 09:35 PM
|
#22 | |
|
Drives: White M6 1LT RS Join Date: Mar 2010
Location: Canton, MI
Posts: 1,676
|
Quote:
Best bang for the buck mod I've done yet. Really brightens up the inside. I don't feel like I am inside a Tank anymore.
__________________
Pfadt Sway Bars - FE3 Suspension - Barton Shifter - IdealG's Clutch Master Cylinder - Trifecta - Vmax TB - Vararam Intake - MACE 25mm Insulator - Plenum Insulator - Ported/Gasket Matched Intake Manifold - Rx Catchcan - AAC DRL's - 4 Pack Aux Gauges - Steering Controls - AAC Afterburners - DIY Led Sidemarkers - ZL1 Front End
Next mod: Done! |
|
|
|
|
|
|
|
|
 |
| Thread Tools | |
|
|
