Adding a ZL1 front end to your car. - Page 120 - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

sene · 02-14-2012, 07:07 PM

snap them in from the back, it confused the hell out of me too for a good hour

jsharp · 02-14-2012, 07:36 PM

Snap in on inside of opening just push and keep them even when pressing in

JPDeMircift · 02-14-2012, 09:12 PM

Quote:

Originally Posted by orangejuice

Does anyone have a picture on how the lower fogs actually attach to the fascia? I think I might need to drill a hole but before I do it want to make sure that there isn't a way that Im not seeing. Anyone? I dont think I am going to be able to use the fogs I got from eBay. I dont think they fit

Here are some pics, hope it helps.

camaro2lt · 02-14-2012, 09:31 PM

can some one post a pic of where the harware goes to hold on the lower fascia like where the threaded things go

jsharp · 02-14-2012, 10:22 PM

drls above in pic will be further foward and retaine will snap in to keep them secure.

2SSRS@Gen5diy · 02-14-2012, 11:58 PM

Quote:

Originally Posted by JPDeMircift

Here are some pics, hope it helps.

What the hell is that with your DRL's where is the retainer

Quote:

Originally Posted by camaro2lt

can some one post a pic of where the harware goes to hold on the lower fascia like where the threaded things go

What parts?

Quote:

Originally Posted by jsharp

drls above in pic will be further foward and retaine will snap in to keep them secure.

+1

JPDeMircift · 02-15-2012, 02:47 AM

Quote:

Originally Posted by 2SSRS

What the hell is that with your DRL's where is the retainer

I don't really know what your referring to that is with my DRL's. All I have there are the lower fogs, DRL's and bumper. And yes I am missing the retainers haha. It doesn't look so bad with everything installed, so until I get them in, I'm rocking the facia without it

Sent from my iPhone using Tapatalk

TripleB · 02-15-2012, 06:17 AM

So, ZL1 production started back up Monday. Think they'll take the hold off ordering parts?

twentytwelvebee · 02-15-2012, 09:38 AM

does anyone know if part #21 would fit on an ss bumper?

jsharp · 02-15-2012, 09:41 AM

nope I bet they dont. Until these really hit the streets I dont think they will release parts. Once they are out and about and have a possibility to have a wreck they will have to release parts but it may even take a vin at that point though!

2SSRS@Gen5diy · 02-15-2012, 09:50 AM

Quote:

Originally Posted by twentytwelvebee

does anyone know if part #21 would fit on an ss bumper?

With some modding it will. Its going on my new leno/T3 bumper

twentytwelvebee · 02-15-2012, 09:56 AM

thanks ofer, looking forward to seeing how it works out.

Quote:

Originally Posted by 2SSRS

With some modding it will. Its going on my new leno/T3 bumper

Mach · 02-15-2012, 10:21 AM

Quote:

Originally Posted by jsharp

nope I bet they dont. Until these really hit the streets I dont think they will release parts. Once they are out and about and have a possibility to have a wreck they will have to release parts but it may even take a vin at that point though!

BS! I don't believe that. The dealer will sell you anything. But if they need a vin I can get one from a showroom ZL1 then.

I'm thinking maybe there is a last minute change/revision in the some of the parts? That's why there is stop on ordering.

2SSRS.. What do you know?

2SSRS@Gen5diy · 02-15-2012, 11:48 AM

I think as soon as cars start moving out from hold parts will be good to go.

And if not there are always other ways.

02-14-2012, 07:36 PM	#1668
jsharp NOW CAMMED & SUPERCHARGED Drives: 2010 Camaro 2SS/RS Black w/ IOM Join Date: Oct 2008 Location: Ar Posts: 2,336	Snap in on inside of opening just push and keep them even when pressing in __________________ Livernois Motorsports: Maggie 2300 7psi, Livernois 2C cam/L99 to LS3 Conversion, Ported TB, Rotofab w/adm race scoop, adm trans cooler,Kooks headers no cats, Kooks 3" exhaust. METCO breather. Precision 2400 Vigilante TC. Eibach Lowering Springs & Swaybars. BMR Trailing arms, BMR Rear Cradle Bushings, BMR Toe Rods, BMR Differential bushings. Vossen CV3 20's w/ 305 Mickey Thompson @25psi. Zl1 front bumper. OE Zl1 Hood and matte black insert. 556RWHP/500RWTQ L99

02-14-2012, 09:31 PM	#1670
camaro2lt Drives: 2010 Camaro 2LT VR/RS CGM Rally's Join Date: May 2009 Location: Palmyra, PA Posts: 5,675 View My Garage	can some one post a pic of where the harware goes to hold on the lower fascia like where the threaded things go __________________ Email: rdurso1@yahoo.com

02-14-2012, 10:22 PM	#1671
jsharp NOW CAMMED & SUPERCHARGED Drives: 2010 Camaro 2SS/RS Black w/ IOM Join Date: Oct 2008 Location: Ar Posts: 2,336	drls above in pic will be further foward and retaine will snap in to keep them secure. __________________ Livernois Motorsports: Maggie 2300 7psi, Livernois 2C cam/L99 to LS3 Conversion, Ported TB, Rotofab w/adm race scoop, adm trans cooler,Kooks headers no cats, Kooks 3" exhaust. METCO breather. Precision 2400 Vigilante TC. Eibach Lowering Springs & Swaybars. BMR Trailing arms, BMR Rear Cradle Bushings, BMR Toe Rods, BMR Differential bushings. Vossen CV3 20's w/ 305 Mickey Thompson @25psi. Zl1 front bumper. OE Zl1 Hood and matte black insert. 556RWHP/500RWTQ L99

02-15-2012, 06:17 AM	#1674
TripleB SoCal Mayhem Drives: 2017 2LT Hyper Blue Metallic Camaro Join Date: May 2009 Location: Lakewood, California Posts: 5,918 View My Garage	So, ZL1 production started back up Monday. Think they'll take the hold off ordering parts? __________________

02-15-2012, 09:41 AM	#1676
jsharp NOW CAMMED & SUPERCHARGED Drives: 2010 Camaro 2SS/RS Black w/ IOM Join Date: Oct 2008 Location: Ar Posts: 2,336	nope I bet they dont. Until these really hit the streets I dont think they will release parts. Once they are out and about and have a possibility to have a wreck they will have to release parts but it may even take a vin at that point though! __________________ Livernois Motorsports: Maggie 2300 7psi, Livernois 2C cam/L99 to LS3 Conversion, Ported TB, Rotofab w/adm race scoop, adm trans cooler,Kooks headers no cats, Kooks 3" exhaust. METCO breather. Precision 2400 Vigilante TC. Eibach Lowering Springs & Swaybars. BMR Trailing arms, BMR Rear Cradle Bushings, BMR Toe Rods, BMR Differential bushings. Vossen CV3 20's w/ 305 Mickey Thompson @25psi. Zl1 front bumper. OE Zl1 Hood and matte black insert. 556RWHP/500RWTQ L99

02-14-2012, 07:07 PM	#1667
sene Drives: 2011 Summit White 2LS Join Date: Jun 2011 Location: Los Angeles Posts: 918	snap them in from the back, it confused the hell out of me too for a good hour

02-15-2012, 09:38 AM	#1675
twentytwelvebee Drives: 2012/2ss "transformers edition" Join Date: Oct 2011 Location: vacaville Posts: 528	does anyone know if part #21 would fit on an ss bumper?

02-15-2012, 11:48 AM	#1680
2SSRS@Gen5diy Drives: 2014 Z/28 #82+#192, 18ZLE 66Nova Join Date: Oct 2008 Location: By the lake in AZ Posts: 15,728 View My Garage	I think as soon as cars start moving out from hold parts will be good to go. And if not there are always other ways.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
CAMARO WIKI	Tran	Wiki	67	11-27-2024 09:02 AM
Gran Turismo 5 November 24th, 2010	Nezacant	Gaming Lounge	562	04-21-2011 10:23 PM
Winner, winner - Jalopnik compares the Big 3	Number 3	5th Gen Camaro SS LS LT General Discussions	31	04-17-2011 04:24 PM
Pedders Suspension Benchmark Track Testing and New Jersey Track Day	Info@PeddersUSA.com	USA - NY / NJ / PA	35	10-26-2009 06:20 PM
#4768 - Delivered and Made Ready the Right Way!	Number_9	5th Gen Camaro SS LS LT General Discussions	62	07-16-2009 03:42 AM