Official UpstateC5 Thread

[Steve]

Subject Change - Clay Baring?

Has anyone clay bared their car? What is the best brand to use? I see bars made by Mothers, Maguire’s, 3M, Pinnacle, and Wolfgang. I am sure there are many more. I watched videos and it does not seem all that hard to do. They say it takes a lot of time but the video doesn't make it look that long or hard to do.

[3CamarosOnHand]

Originally Posted by kjkjr27

So I have been trying to find a place near the Syracuse area to do a couple of dyno runs before I start modding and I came across a place called Jim Ford Dyno that is located in Fulton N.Y. Does anyone know anything about this place?

contact ironwill he lives in oswego

[3CamarosOnHand]

Originally Posted by Steve

Subject Change - Clay Baring?

Has anyone clay bared their car? What is the best brand to use? I see bars made by Mothers, Maguire’s, 3M, Pinnacle, and Wolfgang. I am sure there are many more. I watched videos and it does not seem all that hard to do. They say it takes a lot of time but the video doesn't make it look that long or hard to do.

Steve it doesnt matter all it is is molding clay ,,, they all work the same just make sure the car stays wet wher you are working ,,,lesleigh did the whole car in an hour last night

[3CamarosOnHand]

Some of you were partially right ,but iam not saying with ones ,, you will just have to wait until sunday night or monday morning to go mentally deranged .

[Steve]

Originally Posted by 3CamarosOnHand

Steve it doesnt matter all it is is molding clay ,,, they all work the same just make sure the car stays wet wher you are working ,,,lesleigh did the whole car in an hour last night

OK Andy, Now how do I get Patty to do the job?

[techinny]

Originally Posted by 3CamarosOnHand

Some of you were partially right ,but iam not saying with ones ,, you will just have to wait until sunday night or monday morning to go mentally deranged .

I am going with photo shoot, you've put too much into it recently to get rid of it, unless Lesleigh wants a new car.

And aren't we already mentally deranged enough???

[vinman]

I thought I already was!!! :bangdesk:

[Steve]

Again - New Subject

I am looking at new rims and the supplier I am liking (free shipping) offers only 20X9 with 35 and 40 offsets. I thought the front and back stock rims were 9" and 10" wide? Or is it just the tires that are this width? I am thinking the rims are all only 9" as I don't see anything offered at 10" wide. Is it best to go with the 40 offset all the way round?

[yerHot4TeacherSS]

Oh my....NOOOO I'm NOT Bonnie....NO PHOTOSHOOT w/ ME IN IT.... and yes you all are mentally deranged LOL...... you'll all just have to wait and see

[yerHot4TeacherSS]

Originally Posted by Steve

OK Andy, Now how do I get Patty to do the job?

Steve,
Claybar'ing is very easy actually...you wash the car all down and rinse good get all crap off car and while it is wet and even soapy you rub the claybar all over the car.....I do it because I DRIVE IT but as long as the car is wet while rubbing it works just fine Also, does not matter what one you go with.

[vinman]

Detail spray works good too, do your windows too, they catch a lot of crud too

[vinman]

Toox3, lol

[3CamarosOnHand]

steve get the car wet and hand the clay to patty, but water, soap and rubbing down ,works other ways also ...just saying

[2012 IngotSilver 5.0]

Originally Posted by ssmike

Or maybe Frank talked him into trading in for a new 'stang!

Actually, I talked him into getting the new 348hp Hyundai Genesis.

He told me he wanted a car that was faster than a Camaro SS ... but not as fast as the new 5.0.

Originally Posted by spike III

Thanks a lot ssmike I just got done eating,thought I would turn on comp ... And you just had too post a comment like that. My stomach got all queezzy & I almost up chucked my supper.

*IDEA* - read the forums before you eat