2014 Heat extractor on a 2010 hood - Page 57 - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

Eric-MPD1.com · 07-21-2016, 10:17 PM

Here is a few pictures of a heat extractor install I did on our MPD1 "COPO" style hood a couple weeks ago

rlegendre62@gmail.com · 08-09-2016, 04:01 PM

Hey jerry,
Will this also work on a 2012 v6. I think the hood is the same just wondering about clearance issues

Jerry7297 · 08-11-2016, 09:30 PM

Yes I am pretty sure there would be no issues. There have been plenty of guys on this thread that have completed this and they had V6 cars.

derek1387 · 08-14-2016, 03:34 PM

I just did this, and i have some uneven spots all the way around. The back side doesn't sit flush, but the front does. And the middle bracing is sucking the hood down. Any thoughts?

Shawno72 · 08-14-2016, 03:59 PM

Quote:

Originally Posted by derek1387

I just did this, and i have some uneven spots all the way around. The back side doesn't sit flush, but the front does. And the middle bracing is sucking the hood down. Any thoughts?

Any pics?

derek1387 · 08-14-2016, 04:17 PM

Sent from my iPhone using Tapatalk

Shawno72 · 08-14-2016, 04:49 PM

Awe man Derek. That's why I haven't done this yet. Scare me to death

Ryanbabz71 · 08-14-2016, 05:54 PM

Hole to small? Vent warped?

Ryan

RichSS2006 · 08-14-2016, 07:36 PM

Quote:

Originally Posted by derek1387

I just did this, and i have some uneven spots all the way around. The back side doesn't sit flush, but the front does. And the middle bracing is sucking the hood down. Any thoughts?

My initial install did this too. The hole was a little too tight. I also did not like the foam tape. It made it sit too high, so I removed it. I used black silicone to seal it to the hood. I also did not like the cross bracing as it warped the hood a little. I made a new underside aluminum sheet and use that to mount everything. See my post: http://www.camaro5.com/forums/showth...ternate+method
I've also used Riv-nuts to attach the rain tray.
Good luck, Rich

Jerry7297 · 08-14-2016, 09:32 PM

Hole too small is the 1st thing to come to mind for the uneven results Derek 1387 is getting. That should be verified 1st.

derek1387 · 08-15-2016, 04:48 AM

I thought the hole may be too small as well...but it drops in very very easily and can actually slide around a hair if need be. But I'll double check!

Sent from my iPhone using Tapatalk

Eric-MPD1.com · 08-16-2016, 08:04 AM

Quote:

Originally Posted by RichSS2006

My initial install did this too. The hole was a little too tight. I also did not like the foam tape. It made it sit too high, so I removed it. I used black silicone to seal it to the hood. I also did not like the cross bracing as it warped the hood a little. I made a new underside aluminum sheet and use that to mount everything. See my post: http://www.camaro5.com/forums/showth...ternate+method
I've also used Riv-nuts to attach the rain tray.
Good luck, Rich

Nice job!

xc_SS/RS · 08-27-2016, 09:19 AM

Quote:

Originally Posted by RichSS2006

My initial install did this too. The hole was a little too tight. I also did not like the foam tape. It made it sit too high, so I removed it. I used black silicone to seal it to the hood. I also did not like the cross bracing as it warped the hood a little. I made a new underside aluminum sheet and use that to mount everything. See my post: http://www.camaro5.com/forums/showth...ternate+method
I've also used Riv-nuts to attach the rain tray.
Good luck, Rich

Is it possible for you to have those mounts made? That's a perfect way to attach the extractor. Also did you use a dremel or an air saw?

jrjose107 · 08-28-2016, 09:53 AM

Here's how mine turned out

07-21-2016, 10:17 PM	#785
Eric-MPD1.com Drives: Cool parts for cool cars Join Date: Sep 2009 Location: Riviera Beach FL Posts: 991	Here is a few pictures of a heat extractor install I did on our MPD1 "COPO" style hood a couple weeks ago Attached Images

08-14-2016, 03:34 PM	#788
derek1387 Drives: 2015 1LS Red V6 Join Date: Aug 2015 Location: St Joseph, MO Posts: 1,849	I just did this, and i have some uneven spots all the way around. The back side doesn't sit flush, but the front does. And the middle bracing is sucking the hood down. Any thoughts? __________________ Sponsors: Overkill Motorsport BCS Auto JacFab Machining APDEG Dream Gear Mobile Audio Thanks to Will @ Overkill Motorsports, Jason @ JacFab, Jim @ Ohio Speed, Brandon at Dream Gear, and the boys at Randy Curnow Chevrolet 5th Gen V6 Performance Facebook Group

08-14-2016, 04:17 PM	#790
derek1387 Drives: 2015 1LS Red V6 Join Date: Aug 2015 Location: St Joseph, MO Posts: 1,849	Sent from my iPhone using Tapatalk __________________ Sponsors: Overkill Motorsport BCS Auto JacFab Machining APDEG Dream Gear Mobile Audio Thanks to Will @ Overkill Motorsports, Jason @ JacFab, Jim @ Ohio Speed, Brandon at Dream Gear, and the boys at Randy Curnow Chevrolet 5th Gen V6 Performance Facebook Group

08-14-2016, 04:49 PM	#791
Shawno72 Drives: 2015 Black 2LT RS M6 Join Date: Aug 2015 Location: Cali Posts: 2,033	Awe man Derek. That's why I haven't done this yet. Scare me to death __________________ Overkill tune/E85/80mm•CAI cold air intake w/my custom maf tube•Apex air scoop•JacFab ported intake/Extendolater•Vitesse•EE EX2 catch can•Innovate wideband•ARH HFC's•NPP exhaust•11386 xpipe•Brembos/cross drilled/slotted rotors•SS M/C•Pfadt 1.25 springs•1LE struts/sways/strut tower brace•BMR diff bush, trail arms/bush, adj toe links•My custom Tunnel brace•Hurst short throw shifter•JDP stage 1 clutch res•1LE steering wheel, shift boot•ZL1 rear diffuser/splash guards•GM splitter•Z/28 grille/flowtie/spoiler/wheels•GM performance pedals•"Chevrolet" door sills•10" Kicker sub•BigWorm overlays

08-14-2016, 05:54 PM	#792
Ryanbabz71 Drives: 2021 ZL1 1LE Satin Steel Join Date: Jul 2011 Location: Brownsburg, Indiana Posts: 6,349 View My Garage	Hole to small? Vent warped? Ryan __________________ Ryan 2021 ZL1 1LE Satin Steel Metallic Build Page: https://www.camaro6.com/forums/showthread.php?t=632481

08-09-2016, 04:01 PM	#786
rlegendre62@gmail.com Drives: 2012 camaro Join Date: Nov 2015 Location: flower mound Tx. Posts: 65	Hey jerry, Will this also work on a 2012 v6. I think the hood is the same just wondering about clearance issues

08-11-2016, 09:30 PM	#787
Jerry7297 Drives: 2018 2SS/ 1LE Join Date: Sep 2012 Location: San Marcos TX Posts: 710 View My Garage	Yes I am pretty sure there would be no issues. There have been plenty of guys on this thread that have completed this and they had V6 cars.

08-14-2016, 09:32 PM	#794
Jerry7297 Drives: 2018 2SS/ 1LE Join Date: Sep 2012 Location: San Marcos TX Posts: 710 View My Garage	Hole too small is the 1st thing to come to mind for the uneven results Derek 1387 is getting. That should be verified 1st.

08-15-2016, 04:48 AM	#795
derek1387 Drives: 2015 1LS Red V6 Join Date: Aug 2015 Location: St Joseph, MO Posts: 1,849	I thought the hole may be too small as well...but it drops in very very easily and can actually slide around a hair if need be. But I'll double check! Sent from my iPhone using Tapatalk __________________ Sponsors: Overkill Motorsport BCS Auto JacFab Machining APDEG Dream Gear Mobile Audio Thanks to Will @ Overkill Motorsports, Jason @ JacFab, Jim @ Ohio Speed, Brandon at Dream Gear, and the boys at Randy Curnow Chevrolet 5th Gen V6 Performance Facebook Group

08-28-2016, 09:53 AM	#798
jrjose107 Drives: 2012 2lt camaro rs Join Date: Mar 2015 Location: Phoenix, Az Posts: 63 View My Garage	Here's how mine turned out Attached Images