Installed CAI on 2011 2LT and Stabilitrack light is on - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

SummitWhite11 · 11-04-2016, 07:38 PM

I disconnected the negative battery terminal in the trunk per instructions prior to installation. However, as the title says - the stabilitrack light is on and will not go off. But SH*T!! the car responds so much better and is an animal now! No hesitation at all! I do recall when installing my VMAX TB I had a similar issue and it resolved itself after a few key turns. However, I've been doing this all day riding around town and the check engine light and the warning indicators are still on. Is there a way to reset it?

Dizzy82 · 11-04-2016, 07:58 PM

OBDII scanner will clear the code.

SummitWhite11 · 11-04-2016, 09:04 PM

Quote:

Originally Posted by Dizzy82

OBDII scanner will clear the code.

Thanks!

SummitWhite11 · 11-05-2016, 03:17 PM

Quote:

Originally Posted by Dizzy82

OBDII scanner will clear the code.

After hooking up the OBD II scanner and cleared the codes. I still have two codes showing.

P0113 for Intake Air Temperature Sensor Circuit High Input

P0100 Mass or Volume Air Flow Circuit

I also continue to show warning indicator lights for TC, Skid OFF and Skid ON along with the Service Stabilitrak light.

After trying to clear the codes several times they keep returning. Is there another solution?

Leo72793 · 11-05-2016, 05:03 PM

Quote:

Originally Posted by SummitWhite11

After hooking up the OBD II scanner and cleared the codes. I still have two codes showing.

P0113 for Intake Air Temperature Sensor Circuit High Input

P0100 Mass or Volume Air Flow Circuit

I also continue to show warning indicator lights for TC, Skid OFF and Skid ON along with the Service Stabilitrak light.

After trying to clear the codes several times they keep returning. Is there another solution?

Shut car OFF. wait 30 seconds. unplug MAF and plug firmly back in. Wait 30 seconds. start it up. should clear itself. happened to me on my 2010

SummitWhite11 · 11-05-2016, 09:44 PM

Quote:

Originally Posted by Leo72793

Shut car OFF. wait 30 seconds. unplug MAF and plug firmly back in. Wait 30 seconds. start it up. should clear itself. happened to me on my 2010

Thanks. It worked out great! However the Engine light still remains on. I suppose this will go away after driving for a bit and the computer will relearn itself? Unless I need to check for code?

rtcat600man · 11-06-2016, 04:38 AM

Quote:

Originally Posted by SummitWhite11

I disconnected the negative battery terminal in the trunk per instructions prior to installation. However, as the title says - the stabilitrack light is on and will not go off. But SH*T!! the car responds so much better and is an animal now! No hesitation at all! I do recall when installing my VMAX TB I had a similar issue and it resolved itself after a few key turns. However, I've been doing this all day riding around town and the check engine light and the warning indicators are still on. Is there a way to reset it?

The reason for better "animal" like characteristics, is the car is relearning everything. Once that learning period is over, it will stabilize back to normal.

Leo72793 · 11-06-2016, 07:51 AM

Quote:

Originally Posted by SummitWhite11

Thanks. It worked out great! However the Engine light still remains on. I suppose this will go away after driving for a bit and the computer will relearn itself? Unless I need to check for code?

Pull the code. Make sure your MAF isn't backwards in the intake pipe. Otherwise its read wrong.

SummitWhite11 · 11-06-2016, 07:38 PM

Quote:

Originally Posted by Leo72793

Pull the code. Make sure your MAF isn't backwards in the intake pipe. Otherwise its read wrong.

Ok I pulled the code and it showed a P0100 for the MAF. I had the code erased and now the engine light is no longer showing. I drove it for the day and it seems to be fine. If the light returns then I'll know it's the MAF and I will need to turn it around. However, I'm pretty sure I installed it correctly. Thanks for the help!

Leo72793 · 11-06-2016, 08:26 PM

Quote:

Originally Posted by SummitWhite11

Ok I pulled the code and it showed a P0100 for the MAF. I had the code erased and now the engine light is no longer showing. I drove it for the day and it seems to be fine. If the light returns then I'll know it's the MAF and I will need to turn it around. However, I'm pretty sure I installed it correctly. Thanks for the help!

theres an arrow on it. check it when you can. it can takes up to 50 miles or 5 cycles to pop a code

rtcat600man · 11-07-2016, 04:55 AM

If I remember correctly you can not install the MAF backwards, due to the shape of the housing.

SummitWhite11 · 11-07-2016, 06:42 PM

Quote:

Originally Posted by rtcat600man

If I remember correctly you can not install the MAF backwards, due to the shape of the housing.

Exactly my thoughts since I was pretty sure I put it in the correct way. So far the engine light has not returned and no codes are coming up on Day 2 now.

Sales @ CAI Inc · 11-08-2016, 12:59 PM

Quote:

Originally Posted by SummitWhite11

Exactly my thoughts since I was pretty sure I put it in the correct way. So far the engine light has not returned and no codes are coming up on Day 2 now.

Thanks for purchasing the Cold Air Inductions, Inc. system. We are glad that you are having no issues and that you can feel the performance gains. Thanks again.

SummitWhite11 · 11-08-2016, 06:50 PM

Quote:

Originally Posted by Sales @ CAI Inc

Thanks for purchasing the Cold Air Inductions, Inc. system. We are glad that you are having no issues and that you can feel the performance gains. Thanks again.

11-04-2016, 07:38 PM	#1
SummitWhite11 Drives: 2010 2LT/RS Join Date: Mar 2015 Location: Palm Coast, FL Posts: 1,812	Installed CAI on 2011 2LT and Stabilitrack light is on I disconnected the negative battery terminal in the trunk per instructions prior to installation. However, as the title says - the stabilitrack light is on and will not go off. But SH*T!! the car responds so much better and is an animal now! No hesitation at all! I do recall when installing my VMAX TB I had a similar issue and it resolved itself after a few key turns. However, I've been doing this all day riding around town and the check engine light and the warning indicators are still on. Is there a way to reset it? __________________ 2010 2LT/RS ZL1 Appearance package, Flow Master American Thunder Cat Back Exhaust w/ QUAD TIPS, K&N Typhoon CAI, Ported VMAX TB, OEM GM Brembo Brakes Package w/ Hawks Carbon Ceramic Pads, Night Owl Halo Kit (WIFI), Rear Oracle Blue LED Bowtie, Oracle Ghosted Painted Side LED Markers, Silver Sided Gills, OEM Satin Camaro Fuel Door, OEM Strut Tower Brace, Detroit Speed Engineering 1.5" Lowering Springs, Koni Orange STR.T Struts, Z28 rear LCA's, Black Magic rear 32" sway bar, 1LE front sway bar w/ DSE end links, Aluminum Blend Door, Evil Energy Catch Can.

11-04-2016, 07:58 PM	#2
Dizzy82 Drives: 2011 1LT/RS A6 RJT SuperCharged Join Date: Mar 2011 Location: 87114 Posts: 3,501 View My Garage	OBDII scanner will clear the code. __________________ Power is worthless without control. *The 2nd* protects the 1st.** BMR sub frame brace, BMR tunnel brace, LSR sways, LSR CM ca & tl, Sphon ExD el, GM tower brace, Megan EZ Streets, Goodridge Stainless Steel Braided brake lines, PowerStop D/S rotors & pads, Doug Thorty Ceramic Shorties, Magnaflow x-pipe, MRT V2.0, KICKER PowerStage sub & amp, Infinity speakers & tweeters, Viteese Throttle Controller, Viteese Paddle Shifters, ACS T2 Splitter, ACS T2 Ports/Quad LED lights, VDI kit, Havoc diffuser, IPF ECU/TRANS tuned, IPF/KPE Supercharged. 364RWHP/297RWTQ

11-07-2016, 04:55 AM	#11
rtcat600man having FUN now 13.66@101 Drives: 2010 2LT IOM Join Date: Nov 2009 Location: Clarkston, Michigan Posts: 9,231 View My Garage	If I remember correctly you can not install the MAF backwards, due to the shape of the housing. __________________ MY BUILD