03-25-2014, 09:03 PM | #57 | |
Drives: 2010 ''RS1'' my own package Join Date: Aug 2010
Location: Concord NC
Posts: 237
|
Quote:
__________________
2010 1LT A6, Hurst shifter and handle, 3pc rear spoiler, streetscene splitter, ss front end with ZL1 grill, ABL , footwell and cup holder lighting, ss cat back exhaust, Eibach lowering springs, custom engine cover, 4pk gauges, speedhut A pilliar pod and gauges, metra kit and kenwood stereo, 2014 ss hood scoop with stock rain tray, 3D Carbon fender vents, rear lighted bowtie, and ultra gauge.
|
|
03-25-2014, 10:16 PM | #58 |
03-25-2014, 11:18 PM | #59 |
Drives: SS Join Date: May 2013
Location: Az
Posts: 273
|
How did you make that, just heat gun and a break or did you use the fiberglass as a mold. Did you make a template as well. Very nice work
Last edited by Dexter9522; 03-26-2014 at 12:26 AM. |
03-26-2014, 06:58 AM | #60 |
Drives: 2010 Camaro LS V6 Join Date: Jul 2010
Location: Tampa, Florida
Posts: 2,784
|
prepped and ready for surgery
__________________
C-LO or Sonic
"Without Struggle there is no progress" I am your best nightmare! |
03-26-2014, 07:19 AM | #61 | |
Quote:
I did have a template I had made for the fiberglass piece I made. I used that cut it out and strategically bent the lexan over some angle on one of the trailers at work. the back corners are not sealed so I put silicone on them and plastidipped over. I am very pleased with it and it was a lot easier than the fiberglass. I can upload a template with the measurments for it if anyone would like. The only bad thing is the front 2 mounting nuts were a PITA to get on. |
||
03-26-2014, 07:21 AM | #62 |
03-26-2014, 11:05 AM | #63 |
Drives: 2010 Camaro LS V6 Join Date: Jul 2010
Location: Tampa, Florida
Posts: 2,784
|
Done!
__________________
C-LO or Sonic
"Without Struggle there is no progress" I am your best nightmare! |
03-26-2014, 11:21 AM | #64 |
BUMBL Z
|
man i wanna do this, but i'd be shitting bricks cutting into my hood
__________________
Sold: 2015 ZL1 M6, Rotofab Intake, LS3 throttle body, 2.55 Upper/9.17 Lower, Custom Camshaft, DMS Reinforced Brick, ID1050X, 1 7/8" Headers, ProSpeed HX/Reservoir, DSX Aux Pump/Flex Fuel Sensor, E85, McLeod RXT, BMR 1" Drop, 680rw 93/750rw E85, Tuned by CSP
Sold: 2010 2SS, some bolt ons, 415rwhp/400rwtq |
03-26-2014, 11:25 AM | #65 |
Drives: 2010 Camaro LS V6 Join Date: Jul 2010
Location: Tampa, Florida
Posts: 2,784
|
At worst u cut the hole to small. Then adjust it from there
__________________
C-LO or Sonic
"Without Struggle there is no progress" I am your best nightmare! |
03-26-2014, 12:14 PM | #66 |
Looks really good with your color combo. Would like to see the underneath side... Last edited by Jerry7297; 03-26-2014 at 06:10 PM. |
|
03-26-2014, 05:49 PM | #67 | |
Drives: SS Join Date: May 2013
Location: Az
Posts: 273
|
Quote:
|
|
03-26-2014, 06:07 PM | #68 |
Drives: 2012 RS/SS LS3 Join Date: Jun 2012
Location: Bakersfield, CA
Posts: 873
|
Does anyone have pics of how it mounts on the 2014?
__________________
|
03-26-2014, 06:08 PM | #69 |
03-27-2014, 08:01 AM | #70 |
Drives: 2010 Camaro LS V6 Join Date: Jul 2010
Location: Tampa, Florida
Posts: 2,784
|
this wont work on the 2010-2013 model. the hood is a difference size with the indentions and the hood is made for the actual scoop. i tried yesterday. one of my camaro club members have a 2014. and you would have to play with your 2010 hood and scoop to possibly come up with something to how it would fit let alone stay there. on the 2014 the insulator is different because it has fastener holes as well for the hood scoop pan too
__________________
C-LO or Sonic
"Without Struggle there is no progress" I am your best nightmare! |
|
|
Thread Tools | |
|
|