05-21-2020, 10:01 PM | #1 |
Drives: 15 Camaro SS Join Date: Oct 2018
Location: Mountains of central PA
Posts: 1,442
|
line lock
What brand are you guys using? Looking for a setup that works!
__________________
15 Camaro SS- GPI max top end, ESS Vortech V3 9psi, ID 1050s, ZL1 pump, JMS bap, Long tubes, Corsa extreme, Circle D pro 5C, 391 rear, DSS carbon drive shaft, poly cradle bushings, tuned by Ted Jannetty and much much more
|
05-22-2020, 07:58 AM | #2 |
Drives: 2010 SS L99 Join Date: Sep 2018
Location: Missouri
Posts: 1,635
|
I have the Hurst and it works great
__________________
Previous PB:11.079 @ 122.99mph.. New setup time: TBD
The 11.079 pass: https://youtu.be/pz27Zq54t_E Build thread - www.camaro5.com/forums/showthread.php?t=555371 |
05-22-2020, 08:10 AM | #3 |
Drives: 2010 SS 2SS M6 Join Date: Aug 2016
Location: Smithsburg, Md.
Posts: 2,446
|
TCI...861735
PEACE
__________________
2010 SS 2SS M6 - Tune by RDP dynoSteve!(Woot) - Daily Driver - 150K! - All work by me...
|
05-22-2020, 10:16 AM | #4 |
Account Suspended
Drives: 2013 Sparkly Red One Join Date: Dec 2018
Location: Hospitality State
Posts: 2,558
|
Hurst works
|
05-22-2020, 10:54 AM | #5 |
Drives: 2011 1SS RS Camaro, 1995 LSX 240SX Join Date: Mar 2011
Location: Austin, TX
Posts: 461
|
Hurst. Just make sure you tighten and test. Takes a lot more force than you think to make it not leak under pressure!
__________________
2011 Camaro 1SS
Whipple Supercharged street monster |
05-22-2020, 11:40 AM | #6 |
Drives: 15 Camaro SS Join Date: Oct 2018
Location: Mountains of central PA
Posts: 1,442
|
Thanks guys!
__________________
15 Camaro SS- GPI max top end, ESS Vortech V3 9psi, ID 1050s, ZL1 pump, JMS bap, Long tubes, Corsa extreme, Circle D pro 5C, 391 rear, DSS carbon drive shaft, poly cradle bushings, tuned by Ted Jannetty and much much more
|
05-22-2020, 02:46 PM | #7 |
Drives: 2010 SS L99 Join Date: Sep 2018
Location: Missouri
Posts: 1,635
|
That was the Hurst at work in my sig pic too lol
__________________
Previous PB:11.079 @ 122.99mph.. New setup time: TBD
The 11.079 pass: https://youtu.be/pz27Zq54t_E Build thread - www.camaro5.com/forums/showthread.php?t=555371 |
05-22-2020, 02:59 PM | #8 |
Drives: 2010 SS/RS M6 BIG cam Join Date: Mar 2016
Location: McDonald's DT
Posts: 857
|
Hurst, and yes need to tighten the heck out of the lines
__________________
BIG cam ...... 305 45 18 Mickys ...... BMR suspensions
|
05-22-2020, 03:24 PM | #9 |
Drives: 1980 Chevy corvette Join Date: May 2020
Location: NC
Posts: 17
|
Got any pictures of the interior of the install
|
05-23-2020, 01:09 PM | #10 |
Drives: 2010 SS L99 Join Date: Sep 2018
Location: Missouri
Posts: 1,635
|
Here are some for you
__________________
Previous PB:11.079 @ 122.99mph.. New setup time: TBD
The 11.079 pass: https://youtu.be/pz27Zq54t_E Build thread - www.camaro5.com/forums/showthread.php?t=555371 |
05-23-2020, 01:13 PM | #11 |
Drives: 15 Camaro SS Join Date: Oct 2018
Location: Mountains of central PA
Posts: 1,442
|
__________________
15 Camaro SS- GPI max top end, ESS Vortech V3 9psi, ID 1050s, ZL1 pump, JMS bap, Long tubes, Corsa extreme, Circle D pro 5C, 391 rear, DSS carbon drive shaft, poly cradle bushings, tuned by Ted Jannetty and much much more
|
05-23-2020, 01:14 PM | #12 |
Drives: 15 Camaro SS Join Date: Oct 2018
Location: Mountains of central PA
Posts: 1,442
|
And I love the smokey burnout pic!
__________________
15 Camaro SS- GPI max top end, ESS Vortech V3 9psi, ID 1050s, ZL1 pump, JMS bap, Long tubes, Corsa extreme, Circle D pro 5C, 391 rear, DSS carbon drive shaft, poly cradle bushings, tuned by Ted Jannetty and much much more
|
05-23-2020, 11:06 PM | #13 |
Drives: 1980 Chevy corvette Join Date: May 2020
Location: NC
Posts: 17
|
Car sounds good, what’s the rough numbers it’s putting down? Is that a factory block or aftermarket I’m considering getting a ls3 but still on the fence of the route I’m taking I’m looking for 6-800 hp so. Can just be done with modding the engines for once
|
05-24-2020, 11:57 AM | #14 |
Drives: 2010 SS L99 Join Date: Sep 2018
Location: Missouri
Posts: 1,635
|
The factory block and crank will hold 800rwhp but anything after that and you will want to consider going with a 6.0 depending on what you're shooting for.
__________________
Previous PB:11.079 @ 122.99mph.. New setup time: TBD
The 11.079 pass: https://youtu.be/pz27Zq54t_E Build thread - www.camaro5.com/forums/showthread.php?t=555371 |
|
|
Thread Tools | |
|
|