Down pipes and solo exhaust question - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

ABM Camaro · 10-31-2020, 02:56 PM

Does anyone know if these: https://www.summitracing.com/parts/a...gaAhpqEALw_wcB

Will bolt up to the Solo exhaust without leaking?

Looks like the down pipes are 2 1/2 inch, and the solo exhaust is 2 1/4 inch.

We have been working on this one for quite some time and had to design and manufacture specific “new” products (2 ¼” Mach-X muffler and the Solo angled resonators) to accommodate the design constraints of the car and the very unhealthy natural engine harmonic.

– T409 Mandrel Bent 2.25” Free Flow Piping
– 4.5″ T304 Polished Stainless Steel Round, Beveled Tips
– T304 Stainless Steel (inside and out) Mach X Muffler
– Tuned J Pipes to eliminate drone!!
– Solo’s angled resonators used to calm the noise
– All braces are easily cleared
– Deep, rich, no drone exhaust note
– Fits all V6 convertible Camaro’s
– 100% Bolt-On!!

KillboyPowerhead · 10-31-2020, 08:29 PM

I don't suspect there's be an issue - the cat-back is 2.5" at the beginning, just like the factory pipes, then 2.25" after the centre muffler. The small section from the end of the down pipes to the muffler is 2.5".

10-31-2020, 02:56 PM	#1
ABM Camaro Drives: 2013 ZL1 A6 Camaro Join Date: Jun 2013 Location: Florida Posts: 171	Down pipes and solo exhaust question Does anyone know if these: https://www.summitracing.com/parts/a...gaAhpqEALw_wcB Will bolt up to the Solo exhaust without leaking? Looks like the down pipes are 2 1/2 inch, and the solo exhaust is 2 1/4 inch. We have been working on this one for quite some time and had to design and manufacture specific “new” products (2 ¼” Mach-X muffler and the Solo angled resonators) to accommodate the design constraints of the car and the very unhealthy natural engine harmonic. – T409 Mandrel Bent 2.25” Free Flow Piping – 4.5″ T304 Polished Stainless Steel Round, Beveled Tips – T304 Stainless Steel (inside and out) Mach X Muffler – Tuned J Pipes to eliminate drone!! – Solo’s angled resonators used to calm the noise – All braces are easily cleared – Deep, rich, no drone exhaust note – Fits all V6 convertible Camaro’s – 100% Bolt-On!!

10-31-2020, 08:29 PM	#2
KillboyPowerhead Drives: 2015 Z/22 Join Date: Aug 2015 Location: Ontario, Canada Posts: 937	I don't suspect there's be an issue - the cat-back is 2.5" at the beginning, just like the factory pipes, then 2.25" after the centre muffler. The small section from the end of the down pipes to the muffler is 2.5". __________________ Overkill/Self Tuned; Mace Camshafts; K&N Typhoon Cold Air Intake; Ported 80mm Throttle Body/Intake Manifolds/Manifold Spacer; Solo Performance High-Flow Cats, Cat-back Exhaust; Vitesse Motorsports Throttle Controller; Elite Engineering E2 Catch Can; BC Racing BR Coilovers; JPSS Delrin Radius Rod Bushing Inserts, Sway Bars; Pegasus Aluminum Rear Cradle Bushings, Camber/Caster Plates; Z/28 Toe Links, Trailing Arms, Upper Control Arm Bushings, Rear Shock Mounts