You are browsing camaro5 
 |
|
08-17-2020, 08:41 PM
|
#1 |
        
Drives: 2013 ZL1 416 Join Date: Feb 2013
Location: Langley B.C
Posts: 2,619
|
17" 18" 19" DR'S what fits on stock rear ZL1 Suspension
what size rims and dr's will fit on the stock zl1 rear setup
|
|
|
|
08-18-2020, 06:32 AM
|
#2 |
|
Drives: 2013 ZL1 and 2019 Ram Laramie Join Date: May 2017
Location: Milwaukee
Posts: 1,259
|
Wow...that's a loaded question. Read ProstockJohn's sticky on wheels and tires...it's fairly complete.
|
|
|
|
|
08-21-2020, 09:10 PM
|
#3 |
 
Drives: Red Jewel Camaro SS Join Date: Mar 2014
Location: East Coast
Posts: 395
|
I ran 17".
Tie down the hand brake cable and you may need to trim the sway bar link bolt.On a hard launch,the end of the bolt may touch the rim.
__________________
BTR LSX388,AGP Twin Turbo.6L90,GM 9.9" Diff.Fore Innovations Level 4 fuel system.Great fuel economy !!!! 1xxx RWHP
|
|
|
|
|
08-23-2020, 05:33 PM
|
#4 |
|
mypurpled
Drives: 2014 ZL1 Camaro Join Date: Feb 2020
Location: Hebron Kentucky
Posts: 8
|
Mine are RC Components 17x10 with a 325/45/17 M&H drag radial
|
|
|
|
|
08-23-2020, 08:34 PM
|
#5 | |
|
Drives: 2013 ZL1 416 Join Date: Feb 2013
Location: Langley B.C
Posts: 2,619
|
Quote:
do you know what offset the rims are you used ? |
|
|
|
|
|
08-23-2020, 08:36 PM
|
#6 | |
|
Drives: 2013 ZL1 416 Join Date: Feb 2013
Location: Langley B.C
Posts: 2,619
|
Quote:
do you know what offset the rims are you used ? |
|
|
|
|
|
08-30-2020, 09:06 AM
|
#7 |
|
mypurpled
Drives: 2014 ZL1 Camaro Join Date: Feb 2020
Location: Hebron Kentucky
Posts: 8
|
Check their website.It works out to be around a 7.2” offset.
|
|
|
|
|
12-31-2020, 11:06 PM
|
#8 | |
|
Drives: 2013 ZL1 416 Join Date: Feb 2013
Location: Langley B.C
Posts: 2,619
|
Quote:
|
|
|
|
|
|
01-02-2021, 09:45 AM
|
#9 |
 Drives: 2012 ZL1 Join Date: Mar 2020
Location: Oklahoma City
Posts: 66
|
I run race star 17's with a 315/50, with no issues.
92-705253B
__________________
'12 ZL1 - RPM 5", TSP 2" headers, Speed Engineering 3" header back, Dayco 8.66 lower/LPE 2.38 upper with solid isolator and 10 bolt hub, hand ported blower and snout and went way too far, ID1050x's, DSX aux harness with a summit 400lph pump on E, NGK TR8's with Taylor wires, 160* tstat, NW 102, UPR catch cans, HP Tuners, Stock unopened long block
|
|
|
|
|
|
|
|
 |
|
|
