The Bald Eagle Machine Chronicles

[SlowLS1]

That’s a good price considering the master is being replaced!

Curious how you feel about the RXT. That is what I installed also.

[The_bald_eagle_machine]

As if by some sort of miracle... someone on Facebook messaged me and bought the RXT clutch off of me today. So I will be calling phastek or GPI in the morning and ordering an RST with billet steel flywheel and I'll get what I want and gain some strength while also maintaining my street car status as far as driveabilty with the organic clutch material.

[Leadsled]

That’s a really good price.. I paid 1,100… but he also dropped my oil pan to reseal the gasket

[The_bald_eagle_machine]

I'm asking the shop to give me back all of the old parts, because I want to make a clock or something out of the clutch. Might use the old flywheel as a base for a light or something as well.

[CamaroDreams76]

Honestly the RXT isn't a bad clutch at all. Engagement is a little sharp and rpm is needed to get the clutch to not chatter but it shifts like stock. It's that initial start that isn't great. FBO I got a 2.99.0-60 time..... not 60ft. I'm glad I went with the RXT because an RST wouldn't hold my power level and I wanted to grow into the clutch rather than do it twice.

[The_bald_eagle_machine]

I feel like I should be worried... but I'm not sure. 18-20 psi when hot idling, 30 psi or so when cruising and it peaks at 50 psi or so when getting on it. Should I stop driving it and set aside money for a new oil pump? Or am I OK? I feel like I am just worrying but... can't be too careful.

I also noticed that my headers appear to be "bluing" a bit. I can't recall if they were like that prior to adding boost. Cats look good on the outside, but that doesn't mean anything. Thinking about pulling the headers to wrap them, and gutting the cats while I am in there just to be safe.

[morepowerjoe]

I don't know buddy but I will tell you that those pressures unfortunately aren't going to get any better. The bypass relief valve in the pan is what's causing it to only get up to 50 psi or so under wot. As far as idle pressure goes that's a completely different animal. It's something that pelages' many of us LS owners sooner or later. Don't know what the real cause is I just know how to fix it. A high volume pump and plug that relief valve. You can get some of CFG's (I think that's his username) to make that crossmember a bolt in one to be able and get the pan off without pulling the engine.

[CamaroDreams76]

Originally Posted by The_bald_eagle_machine

I feel like I should be worried... but I'm not sure. 18-20 psi when hot idling, 30 psi or so when cruising and it peaks at 50 psi or so when getting on it. Should I stop driving it and set aside money for a new oil pump? Or am I OK? I feel like I am just worrying but... can't be too careful.

I also noticed that my headers appear to be "bluing" a bit. I can't recall if they were like that prior to adding boost. Cats look good on the outside, but that doesn't mean anything. Thinking about pulling the headers to wrap them, and gutting the cats while I am in there just to be safe.

My stock pump would idle around that. It would be 20-24 hot, average was 22/23. If I was spritied driving or doing autocross hot idle would dip to that 18-19 mark which always worried me.

[SlowLS1]

CFD is the guy that makes the weld in parts for the bolted crossmember.

You are on the low side for idle oil pressure, but I don't think it's dire. As for bluing on the headers, looks pretty normal to me for stainless headers.

[Bee]

Back when I had my cam installed by East Coast Supercharging, one of the many things they installed was a Melling 10296.

Although this entire thread is a great read, Post #52 is certainly note worthy:
https://www.camaro5.com/forums/showt...=254409&page=4

[The_bald_eagle_machine]

The CFD oil pan kit is definitely on my list. I do plan on camming the car early next year and had budgeted the High pressure/High Volume Melling pump in that install. I guess If things get any worse then this, I will put the car into hibernation for awhile before anything gets damaged.

[Stormes_1SS]

This is such a good journal/build thread. Howard tuned my FBO car and it was a totally different animal. I’ve been researching torqstorm and stumbled upon your profile. Keep up the awesome work. I’ll be tuning in for updates.

[The_bald_eagle_machine]

Originally Posted by Stormes_1SS

This is such a good journal/build thread. Howard tuned my FBO car and it was a totally different animal. I’ve been researching torqstorm and stumbled upon your profile. Keep up the awesome work. I’ll be tuning in for updates.

Check out my instagram, I have tons of videos and content relating to the Torqstorm kit. I can provide any or as much insight as you want. I personally love the blower. If you want to keep it under 10 psi on a stock motor, the Torqstorm is great.

[The_bald_eagle_machine]

My car is at the shop getting the clutch put in, so im just thinking about her and felt like posting some pictures.