Premium 370.1 ring and pinion - Page 2 - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

nak3dsnake · 02-13-2011, 12:34 PM

And to those of you who don't know. This will fit in an M6 V6. Its been done with 3.73s, look it up. We have the same rear end as the A6 SS.

nuptualnemesis · 02-15-2011, 05:11 PM

Quote:

Originally Posted by nak3dsnake

Do you still have this?

Yes.

nuptualnemesis · 02-17-2011, 05:46 AM

Quote:

Originally Posted by 2010 2-Tone

What is your best time with the 4.33's?

Got Traction last night.

2010 2-Tone · 02-17-2011, 05:01 PM

1.6 60ft is really good. 11.5 is haulin ass!!!!! I hope to run a 12.5 Great job with those runs.

Gbusy06 · 02-26-2011, 08:00 PM

Nuptuals, I met you at No Problem a few months ago. I am tempted to buy the gear but first, I must consult with my mechanic. I will be at No Problem this Wednesday. I met you when I had a Jeep SRT8 and my buddy had a brand new 2010 2ss. Well, I ended up buying a 2ss Cyber Gray. I know Angie at Thunder. But anyway, I will see you Wednesday if you are there at No Problem.

nuptualnemesis · 02-28-2011, 12:43 PM

I ran 11.5 at no problem a week and a half ago. It may be a while before I go back to No Problem. I will probably run my 77 Cobra II mustang at State Capitol Sunday. It has a 347 stroker, solid roller lifter and weighs 2,900 lbs. Working on trying to get it to hook.

If you get a gear, I highly recommend Zimmer Gears for installation. They put in my 4:33 and have the experience, housing spreader, and depth gauges to do it right. I did not use the billet end caps, but my gears are making a little noise, so you might want to try them. The caps have to milled, so it adds a little to the cost. Zimmer was a whole lot cheaper than Jannetty Racing and two day turn around. I pulled the center section and dropped it off.

Good luck.

Mark

BoostedX2 · 03-01-2011, 04:27 AM

Nuptial, I broke my 4.10s and am cosidering Zimmer to put my stock ones back in my case. Can they do the whole job? It will need new bearings, shims, etc. Thanks!
Tom

nuptualnemesis · 03-01-2011, 11:38 AM

Call them and ask what they need from you and a price. They have my extra shims and I think they have bearings but a richmond half or full install kit may still be necessary. I am sure they can get it for you from richmond at a discount.

(225) 927-6125

azvren · 03-08-2011, 08:31 PM

What gear are you in at the end of the qtr and what rpm with those 4.33s?

nuptualnemesis · 03-09-2011, 05:15 PM

20" nittos trap around 6,400 rpm at 120-121mph in 4th.

nuptualnemesis · 03-18-2011, 04:13 PM

SOLD!

02-13-2011, 12:34 PM	#15
nak3dsnake Drives: 2010 Camaro IBM 2LT/RS M6 Join Date: Sep 2009 Location: Columbus, OH Posts: 2,282 View My Garage	And to those of you who don't know. This will fit in an M6 V6. Its been done with 3.73s, look it up. We have the same rear end as the A6 SS. Last edited by nak3dsnake; 02-13-2011 at 02:07 PM.

02-28-2011, 12:43 PM	#20
nuptualnemesis NuptualNemesis Drives: Silver 1SS M6 - 480hp 11.57/120.79 Join Date: Jul 2009 Location: Baton Rouge, LA www.Divorcefor399.com Posts: 310 View My Garage	gear I ran 11.5 at no problem a week and a half ago. It may be a while before I go back to No Problem. I will probably run my 77 Cobra II mustang at State Capitol Sunday. It has a 347 stroker, solid roller lifter and weighs 2,900 lbs. Working on trying to get it to hook. If you get a gear, I highly recommend Zimmer Gears for installation. They put in my 4:33 and have the experience, housing spreader, and depth gauges to do it right. I did not use the billet end caps, but my gears are making a little noise, so you might want to try them. The caps have to milled, so it adds a little to the cost. Zimmer was a whole lot cheaper than Jannetty Racing and two day turn around. I pulled the center section and dropped it off. Good luck. Mark

03-01-2011, 11:38 AM	#22
nuptualnemesis NuptualNemesis Drives: Silver 1SS M6 - 480hp 11.57/120.79 Join Date: Jul 2009 Location: Baton Rouge, LA www.Divorcefor399.com Posts: 310 View My Garage	Zimmer Gear Call them and ask what they need from you and a price. They have my extra shims and I think they have bearings but a richmond half or full install kit may still be necessary. I am sure they can get it for you from richmond at a discount. (225) 927-6125

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
FS BARTON SHORT THROW SHIFTER AND RICHMON 4:10 RING AND PINION	stephancamaro	Transmission / Driveline	7	11-24-2010 07:33 PM
WTB 3.73s	jay11	V8 and V6 Transmissions / Driveline (6L80 / 6L50 / TR6060 / AY6)	10	09-10-2010 07:59 AM
Ring & Pinion INSTALL KITS.	Qwkss	V8 and V6 Transmissions / Driveline (6L80 / 6L50 / TR6060 / AY6)	14	03-31-2010 12:25 AM
Ring & Pinion Swap Out	SJ LYNN	V8 and V6 Transmissions / Driveline (6L80 / 6L50 / TR6060 / AY6)	15	02-18-2010 08:44 PM
Is a ring and pinion whine normal for 2002 V6?	TopFuelTim	4th Generation Camaros	7	04-09-2009 08:51 PM

02-17-2011, 05:01 PM	#18
2010 2-Tone Drives: 2010 RY 2SS with Custom Stripes Join Date: Mar 2009 Location: Jennings, La. Posts: 2,220 View My Garage	1.6 60ft is really good. 11.5 is haulin ass!!!!! I hope to run a 12.5 Great job with those runs.

02-26-2011, 08:00 PM	#19
Gbusy06 Tap Out Drives: 2011 Camaro SS A6 SGM Join Date: Oct 2010 Location: USA Posts: 189	Nuptuals, I met you at No Problem a few months ago. I am tempted to buy the gear but first, I must consult with my mechanic. I will be at No Problem this Wednesday. I met you when I had a Jeep SRT8 and my buddy had a brand new 2010 2ss. Well, I ended up buying a 2ss Cyber Gray. I know Angie at Thunder. But anyway, I will see you Wednesday if you are there at No Problem.

03-01-2011, 04:27 AM	#21
BoostedX2 Drives: VR ZL1 #259/Nissan 370Z NISMO Join Date: Aug 2008 Location: Ohio Posts: 1,071	Nuptial, I broke my 4.10s and am cosidering Zimmer to put my stock ones back in my case. Can they do the whole job? It will need new bearings, shims, etc. Thanks! Tom

03-08-2011, 08:31 PM	#23
azvren Drives: Camaro 2SS RS IBM Join Date: Jan 2009 Location: Odessa, Tx Posts: 258	What gear are you in at the end of the qtr and what rpm with those 4.33s?

03-09-2011, 05:15 PM	#24
nuptualnemesis NuptualNemesis Drives: Silver 1SS M6 - 480hp 11.57/120.79 Join Date: Jul 2009 Location: Baton Rouge, LA www.Divorcefor399.com Posts: 310 View My Garage	20" nittos trap around 6,400 rpm at 120-121mph in 4th.

03-18-2011, 04:13 PM	#25
nuptualnemesis NuptualNemesis Drives: Silver 1SS M6 - 480hp 11.57/120.79 Join Date: Jul 2009 Location: Baton Rouge, LA www.Divorcefor399.com Posts: 310 View My Garage	SOLD!