10-15-2013, 11:20 AM | #57 |
Oldbie that nobody knows
|
Removed the dash again, this time I made sure I plugged in the night sensor (Good GOD is that stupid little connector a bitch to thread to the right spot), and I aligned the clockspring correctly... Stabilitrak Service code is gone! Thanks again.
|
04-26-2014, 05:45 PM | #58 |
Drives: 2010 Chevrolet Camaro 2SS Join Date: Jun 2013
Location: Crane, TX
Posts: 6
|
So I'm installing HUD into my camaro and ran into a problem. When your trying to take out the steering wheel. I push in the spring on the left side and it pops off. But when I try to push in the spring on the right side the thing doesn't want to come off. Any suggestion
Sent from my XT1080 using Tapatalk |
04-26-2014, 07:02 PM | #59 | |
I wanna go fast!!!!
Drives: 2010 SS/RS Inferno Orange Metallic Join Date: Dec 2010
Location: Fennville, MI
Posts: 332
|
Quote:
Sent using Tapatalk
__________________
Proud Member Dayton Camaro Club (DCC) http://www.camaro5.com/forums/group.php?groupid=412
And on Facebook https://www.facebook.com/groups/DaytonCamaroClub/ |
|
04-30-2014, 11:21 PM | #60 | |
Drives: 2010 Chevrolet Camaro 2SS Join Date: Jun 2013
Location: Crane, TX
Posts: 6
|
Quote:
Sent from my XT1080 using Tapatalk |
|
05-01-2014, 07:24 PM | #61 |
I wanna go fast!!!!
Drives: 2010 SS/RS Inferno Orange Metallic Join Date: Dec 2010
Location: Fennville, MI
Posts: 332
|
With the airbag facing down, pull up gently on the back of each connector. There is a lock on each, the back of each will pull up. You will know when u do it right as it will click. Then you can pull each plug off.
Sent using Tapatalk
__________________
Proud Member Dayton Camaro Club (DCC) http://www.camaro5.com/forums/group.php?groupid=412
And on Facebook https://www.facebook.com/groups/DaytonCamaroClub/ |
05-01-2014, 07:26 PM | #62 |
Drives: 2010 Chevrolet Camaro 2SS Join Date: Jun 2013
Location: Crane, TX
Posts: 6
|
Nice I'll try that.
Sent from my XT1080 using Tapatalk |
05-01-2014, 07:29 PM | #63 |
Drives: 2010 Chevrolet Camaro 2SS Join Date: Jun 2013
Location: Crane, TX
Posts: 6
|
Do you know the part number that the wire is attached too.
Sent from my XT1080 using Tapatalk |
05-01-2014, 08:16 PM | #64 | |
I wanna go fast!!!!
Drives: 2010 SS/RS Inferno Orange Metallic Join Date: Dec 2010
Location: Fennville, MI
Posts: 332
|
Quote:
Sent using Tapatalk
__________________
Proud Member Dayton Camaro Club (DCC) http://www.camaro5.com/forums/group.php?groupid=412
And on Facebook https://www.facebook.com/groups/DaytonCamaroClub/ |
|
10-22-2016, 10:53 PM | #65 |
Drives: 2010 RJT 2SS M6 Camaro Join Date: Feb 2011
Location: Garrison,KY
Posts: 1,548
|
Ok, I fnially got around to doing this after having Ofers color HUD kit laying around for over a year. It went well, but there was a couple of screws that weren't mentioned in the instructions. One under the defroster vent,which IS shown in that shop manual exploded view at the begining of this thread, but NOT mentioned in the text. The other one is behind the dash in between the HUD control switch and the radio and it is a bitch to get to. It's easier to put back in because you can see it through the HUD switch opening.I think it would be easier to remove that plastic knee cushion that's behind the dash, along with the dash. I think there is only one bolt holding it in and the hood release would have to be removed. That's the way the junkyard that I bought the 2014 dash from, removed it.
__________________
2010 RJT 2SS M6, Kooks Long Tubes, NPP Exhaust, CAI Cold Air w/Jannetty Scoop, RotoFab Washer Bottle, Elite Engineering Catch Can, MGW Shifter w/ZL1 Shaft and Knob, 2015 SS Sedan Steering Wheel and Air Bag, 2012 Heater Hose Conversion, 2012 Power Seat Conversion, RS Head Lights,Gen5DIY RS Conversion Harness, LED Fog Lamp Bulbs, Backup Camera Kit, NLP Spoiler, SLP Splitter, ZL1 Rockers and Diffuser, Color Matched Shark Fin, RS Roof Mouldings, Painted White Stripes, WCC LS3 Emblems, Heritage Grille and Blacked Out Tail Light Panel w/Retro SS Emblems, 416 RWHP, 411 RWT, Tuned by BlueCat.
|
04-12-2017, 08:12 PM | #66 |
Drives: 2014 1le 1SS CRMT Join Date: Apr 2014
Location: Boston mass
Posts: 1,185
|
|
04-13-2017, 08:42 AM | #67 |
Drives: 2014 Z/28 #82+#192, 18ZLE 66Nova Join Date: Oct 2008
Location: By the lake in AZ
Posts: 15,719
|
Not in a 14 1ss, you will need to call us and we can walk you true the checks to see how your car is wired.
|
04-13-2017, 10:25 AM | #68 |
Drives: 2014 1le 1SS CRMT Join Date: Apr 2014
Location: Boston mass
Posts: 1,185
|
Ok ok thanks
|
04-13-2017, 04:03 PM | #69 |
Drives: 2014 1le 1SS CRMT Join Date: Apr 2014
Location: Boston mass
Posts: 1,185
|
Hope this isn't going to be a nightmare?!? I was a 12 volt installed for 18 years !! I'm not afraid of taking the dash & things apart .. Just how many more things am I going to need to get it done correctly ?!?
|
04-13-2017, 06:04 PM | #70 |
Drives: 2014 Z/28 #82+#192, 18ZLE 66Nova Join Date: Oct 2008
Location: By the lake in AZ
Posts: 15,719
|
Some 14-15 1LE don't have all the wires so you need to find if there there and hot, call if you want our help.
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
CAMARO WIKI | Tran | Wiki | 66 | 04-22-2024 11:41 AM |
Gran Turismo 5... No Camaro? | 5thGenOwner | 5th Gen Camaro SS LS LT General Discussions | 111 | 12-06-2011 10:06 AM |
GM memo to dealers | Moose | 5th Gen Camaro SS LS LT General Discussions | 41 | 02-04-2010 07:33 PM |