12-04-2012, 06:20 PM | #785 |
Drives: 2014 1LS M6 Supercharged Join Date: Feb 2011
Location: New Britain, Ct
Posts: 937
|
Was visiting here in Fl. so had to make a trip to RX Performance to check out the shop, met Tracy, He showed me around, showed me "Chakita" The Cammed Camaro, then gave me a Test Drive, Very impressive, first of all, it has such a nice Growl,(and I can't emphasize enough how nice it sound at idle, like listining to a V8) and when you get on it, boy does it pull nicely on the top end.
|
12-04-2012, 06:52 PM | #786 | |
Drives: 2011 1LT "Chakita". 04 Yota Join Date: Jun 2011
Location: Round Rock, TX
Posts: 823
|
Quote:
__________________
Hi, my name is Chakita. I have cams!!!!
Build thread: http://www.camaro5.com/forums/showthread.php?p=3847083 |
|
12-05-2012, 09:52 PM | #787 |
Drives: 2011 CGM 2LT/RS Join Date: May 2011
Location: Round Rock, TX
Posts: 394
|
Go get your car!! Seriously when are you going?
|
12-06-2012, 07:30 AM | #788 |
Drives: LLT Machine Join Date: Nov 2011
Location: VIC/AUS
Posts: 563
|
I want a ride too Bit of a hike though LOL :(
|
12-06-2012, 08:25 AM | #789 |
Guest
|
Uhm someone stole the heads... Can't really go too far.
. . . . Just kidding ! We're putting on a set of RX Performance Port/Polished Cylinder Heads!!! |
12-06-2012, 09:13 AM | #790 |
Guest
|
Dynojet sheet...
|
12-06-2012, 09:15 AM | #791 |
Drives: 16 Camaro SS, 15 Colorado Join Date: May 2009
Location: Jefferson City, Missouri
Posts: 13,950
|
Looking forward to the final result with the heads!
__________________
2016 Camaro 1SS - 8-speed - NPP - Black bowties
2010 Camaro 1LT V6 (Sold. I will miss her!) |
12-06-2012, 09:33 AM | #792 |
Formerly Camaroc5
Drives: 2010 Camaro LT/RS M6 Join Date: May 2010
Location: USA
Posts: 1,647
|
I am surprised with the 284 on the dyno sheet. Isn't that what a modded car is pulling without cams? Or close to it?
Sent from my DROID RAZR using Tapatalk 2 |
12-06-2012, 09:38 AM | #793 |
Engineer in Training
Drives: IBM 2010 Camaro LS Join Date: Nov 2011
Location: Alabama
Posts: 292
|
Where is the before dyno sheet?
I've looked, but man there are a lot of posts in this thread.
__________________
K&N Aircharger CAI, BBK LT's, VMAX black ICE, Trifecta tuned
|
12-06-2012, 10:32 AM | #794 |
|
I think the before read 250ish with mods (pretty sure it's reading low) so this shows a 30 rwhp gain.
__________________
|Trifecta Tune|Custom Magnaflow Exhaust|Cold Air Inductions C.A.I.|BBK LTs w/ HFC|Anvil Rear Notch Glossy CF Spoiler|Body Color Heritage Grille|10 spoke polished ZL1 replica wheels|VMAX ported TB|RS Headlights|Night Owl RGB Halos
|
12-06-2012, 11:22 AM | #795 | |
Drives: 2011 1LT "Chakita". 04 Yota Join Date: Jun 2011
Location: Round Rock, TX
Posts: 823
|
Quote:
Had visions of getting banned on my own thread... Lol! Somebody stole the heads... You guys!! Ideally - get the heads done and tuned, would be a treat to see a couple of passes at Bradenton. Would be another validation point of the cars gains. Work will play a factor also - worst case I'll fly out for a couple of days and ship the car back - day job I'd definitely gettin in the way of fun stuff!
__________________
Hi, my name is Chakita. I have cams!!!!
Build thread: http://www.camaro5.com/forums/showthread.php?p=3847083 Last edited by Yellow_Glide; 12-06-2012 at 07:16 PM. |
|
12-06-2012, 11:22 AM | #796 |
Was the cammed dyno done with the isolator on?
|
|
12-06-2012, 11:25 AM | #797 |
Drives: 2011 1LT "Chakita". 04 Yota Join Date: Jun 2011
Location: Round Rock, TX
Posts: 823
|
Yes, on for baseline and final runs
__________________
Hi, my name is Chakita. I have cams!!!!
Build thread: http://www.camaro5.com/forums/showthread.php?p=3847083 |
12-06-2012, 11:42 AM | #798 |
Can't wait to see what the heads do. Are they going to dyno ported heads and manifold together or one at the time?
|
|
|
|
|
|