LED's under shifter boot - Page 7 - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

TwentyTen2SSRS · 06-08-2014, 12:16 PM

This is where I'm at.. Light in in and wrapped around and my console removed... Don't know where to go from here.

Sent from my iPhone using Tapatalk 2

CamaroI · 06-08-2014, 12:28 PM

You can merge all wires together "hot ones" from footwells and other LEDs wanting to connect them run one will re to the cig red wire.

Sent from my iPhone using Tapatalk

CamaroI · 06-08-2014, 12:30 PM

Quote:

Originally Posted by TwentyTen2SSRS

This is where I'm at.. Light in in and wrapped around and my console removed... Don't know where to go from here.

Sent from my iPhone using Tapatalk 2

I would also snap the clam shell back on real quick and see how much of the tube actually seeing. You might find not as much as you thought. I could hardly see mine unless at an angle. If not something we'll viewed I didn't want to keep it

Sent from my iPhone using Tapatalk

LnLSS · 06-08-2014, 12:34 PM

Quote:

Originally Posted by TwentyTen2SSRS

Man. I know this should be so simple. Do you even need the ground wire, or just the positive to the red on the cigarette lighter? I did this on my LS, but the set up was different under here - I didn't have the 4 aux guagues, and the wire was not this huge thick red one to the cigarette lighter. I don't think my 14-16 gauge t-taps can even tap this wire.

Yes you need ground too

TwentyTen2SSRS · 06-08-2014, 12:40 PM

Quote:

Originally Posted by LnLSS

Yes you need ground too

Where do I ground all of this too?

Are we sure we tap into the red wire on cig lighter, it seems really thick and tough to tap into

CamaroI · 06-08-2014, 12:46 PM

Little off topic but still the same I started a Facebook page today title 2010+ Camaro mods..when get completed would be great to have a write up there with photos.

Sent from my iPhone using Tapatalk

CamaroI · 06-08-2014, 12:48 PM

You can tap into any power source. You could even strip with re a bit and tie into. I did that with my footwells already installed in the front. The ones in back I spliced into the red power wire and taped up. Zero issues.

Sent from my iPhone using Tapatalk

TwentyTen2SSRS · 06-08-2014, 01:16 PM

Can I ground to any of these screws here?

Sent from my iPhone using Tapatalk 2

LnLSS · 06-08-2014, 01:24 PM

No but there is a screw on each side if you pull off the side panel a little.

TwentyTen2SSRS · 06-08-2014, 01:44 PM

Got it... Finally!

Sent from my iPhone using Tapatalk 2

Jcashan · 06-08-2014, 01:44 PM

Quote:

Originally Posted by CamaroI

I did but didn't waste time taking install photos. I also removed it because not enough light coming through and I could see the tube. This may be in part having an automatic converters over. The boot just got in the way and wasn't even all around. The tube IMO sits too low and clam shells covers too much. Your more seeing the tube at-least on mine from the side. If that makes sense.
However this is the light source I found at pep boys

Sent from my iPhone using Tapatalk

Sorry to hear that... That sucks !

Jcashan · 06-08-2014, 01:46 PM

Quote:

Originally Posted by TwentyTen2SSRS

Got it... Finally!

Sent from my iPhone using Tapatalk 2

TwentyTen2SSRS · 06-08-2014, 01:50 PM

Lol... Only trouble was I was doing the footwells at the same time. Threw slight curveball for me -

Sent from my iPhone using Tapatalk 2

TwentyTen2SSRS · 06-08-2014, 04:45 PM

Sent from my iPhone using Tapatalk 2

06-08-2014, 12:16 PM	#85
TwentyTen2SSRS Drives: 2010 2SS/RS Join Date: Apr 2013 Location: Seattle, WA Posts: 3,974 View My Garage	This is where I'm at.. Light in in and wrapped around and my console removed... Don't know where to go from here. Sent from my iPhone using Tapatalk 2 __________________ Cold Air Inductions CAI • Stainless Power LT's with HFC's • Flowmaster American Thunder Cat Back • APEX Scoop and WW Relocation Kit • VMAX Ported Throttle Body • Custom Dyno Tune • Pfadt 1.25" Lowering Springs • ZL1 Rims on 275 front 315 Rear • custome underlay vinyl wrap • Anvil Spoiler • heritage grill • APR Front Splitter • Custom Emblempros emblems • ZL1 Side Skirts • 416.5 whp 410 torque (CURRENTLY) Up Next: BTR Stage 3 Cam and supporting mods (in garage now)

06-08-2014, 01:16 PM	#92
TwentyTen2SSRS Drives: 2010 2SS/RS Join Date: Apr 2013 Location: Seattle, WA Posts: 3,974 View My Garage	Can I ground to any of these screws here? Sent from my iPhone using Tapatalk 2 __________________ Cold Air Inductions CAI • Stainless Power LT's with HFC's • Flowmaster American Thunder Cat Back • APEX Scoop and WW Relocation Kit • VMAX Ported Throttle Body • Custom Dyno Tune • Pfadt 1.25" Lowering Springs • ZL1 Rims on 275 front 315 Rear • custome underlay vinyl wrap • Anvil Spoiler • heritage grill • APR Front Splitter • Custom Emblempros emblems • ZL1 Side Skirts • 416.5 whp 410 torque (CURRENTLY) Up Next: BTR Stage 3 Cam and supporting mods (in garage now)

06-08-2014, 01:44 PM	#94
TwentyTen2SSRS Drives: 2010 2SS/RS Join Date: Apr 2013 Location: Seattle, WA Posts: 3,974 View My Garage	Got it... Finally! Sent from my iPhone using Tapatalk 2 __________________ Cold Air Inductions CAI • Stainless Power LT's with HFC's • Flowmaster American Thunder Cat Back • APEX Scoop and WW Relocation Kit • VMAX Ported Throttle Body • Custom Dyno Tune • Pfadt 1.25" Lowering Springs • ZL1 Rims on 275 front 315 Rear • custome underlay vinyl wrap • Anvil Spoiler • heritage grill • APR Front Splitter • Custom Emblempros emblems • ZL1 Side Skirts • 416.5 whp 410 torque (CURRENTLY) Up Next: BTR Stage 3 Cam and supporting mods (in garage now)

06-08-2014, 01:50 PM	#97
TwentyTen2SSRS Drives: 2010 2SS/RS Join Date: Apr 2013 Location: Seattle, WA Posts: 3,974 View My Garage	Lol... Only trouble was I was doing the footwells at the same time. Threw slight curveball for me - Sent from my iPhone using Tapatalk 2 __________________ Cold Air Inductions CAI • Stainless Power LT's with HFC's • Flowmaster American Thunder Cat Back • APEX Scoop and WW Relocation Kit • VMAX Ported Throttle Body • Custom Dyno Tune • Pfadt 1.25" Lowering Springs • ZL1 Rims on 275 front 315 Rear • custome underlay vinyl wrap • Anvil Spoiler • heritage grill • APR Front Splitter • Custom Emblempros emblems • ZL1 Side Skirts • 416.5 whp 410 torque (CURRENTLY) Up Next: BTR Stage 3 Cam and supporting mods (in garage now)

06-08-2014, 04:45 PM	#98
TwentyTen2SSRS Drives: 2010 2SS/RS Join Date: Apr 2013 Location: Seattle, WA Posts: 3,974 View My Garage	Sent from my iPhone using Tapatalk 2 __________________ Cold Air Inductions CAI • Stainless Power LT's with HFC's • Flowmaster American Thunder Cat Back • APEX Scoop and WW Relocation Kit • VMAX Ported Throttle Body • Custom Dyno Tune • Pfadt 1.25" Lowering Springs • ZL1 Rims on 275 front 315 Rear • custome underlay vinyl wrap • Anvil Spoiler • heritage grill • APR Front Splitter • Custom Emblempros emblems • ZL1 Side Skirts • 416.5 whp 410 torque (CURRENTLY) Up Next: BTR Stage 3 Cam and supporting mods (in garage now)

06-08-2014, 12:28 PM	#86
CamaroI Drives: 2010 IOM Camaro Join Date: Aug 2012 Location: DFW Posts: 3,112	You can merge all wires together "hot ones" from footwells and other LEDs wanting to connect them run one will re to the cig red wire. Sent from my iPhone using Tapatalk

06-08-2014, 12:46 PM	#90
CamaroI Drives: 2010 IOM Camaro Join Date: Aug 2012 Location: DFW Posts: 3,112	Little off topic but still the same I started a Facebook page today title 2010+ Camaro mods..when get completed would be great to have a write up there with photos. Sent from my iPhone using Tapatalk

06-08-2014, 12:48 PM	#91
CamaroI Drives: 2010 IOM Camaro Join Date: Aug 2012 Location: DFW Posts: 3,112	You can tap into any power source. You could even strip with re a bit and tie into. I did that with my footwells already installed in the front. The ones in back I spliced into the red power wire and taped up. Zero issues. Sent from my iPhone using Tapatalk

06-08-2014, 01:24 PM	#93
LnLSS Mid-Florida Camaro Club Drives: 2015 Red Hot ZL1 Join Date: Jul 2007 Location: Orlando Fla Posts: 2,581 View My Garage	No but there is a screw on each side if you pull off the side panel a little.