Street Scene Camaro SS aero / body kit

[ElManny]

well i got the answer to my question :

Thanks for your inquiry Manuel regarding Street Scene products for your Chevy Camaro. The part number for the street scene billet grille in black with a black billet grille is 950-85224. This fits the SS model only. We have not developed the grilles with ducts for the V6 or RS model as of yet. We expect to have the V6/RS model grilles and ducts ready in late December.

it shows up on summit racing and they have it for $242.99

[ajp]

Originally Posted by SSPROJECT

J & J TRI COLOR in santa ana ask for JACK he painted and installed it. i paid $2000 just for paint and install. you can get different prices on paint and install but everyone does different types of labor and paint. so you can find cheaper or more. i would give at least 3-5 days of time needed.

Ouch $2000 for install and paint? Most dealers are charging $300 install and $600 paint for the GM GFX. Is this kit harder to install?

Does it go on with tape only or bolts?

[ElManny]

Originally Posted by ajp

Ouch $2000 for install and paint? Most dealers are charging $300 install and $600 paint for the GM GFX. Is this kit harder to install?

Does it go on with tape only or bolts?

if you go to streetsceneeq.com they have the instruction sheets

http://streetsceneeq.com/searchresul...=2010&x=6&y=17

[Stang Stomper]

Originally Posted by montej23

OK I want the Rear spoiler where do i order it from does anyone know?

AutoAnything's pieced out the whole Street Scene kit, you can find the spoiler there: http://www.autoanything.com/body-kit...15A2680A1.aspx

[SSPROJECT]

Originally Posted by ajp

Ouch $2000 for install and paint? Most dealers are charging $300 install and $600 paint for the GM GFX. Is this kit harder to install?

Does it go on with tape only or bolts?

i know the $2000 might be on the high side but if you go to five different bodyshops and ask them for a price you are going to get 5 different prices. the paint brand also can make the price go up also the street scene kit which i paid to have painted an installed also included the trunk spoiler install and front grills and air ducts install also i had some cosmetic changes. but it is average price for that job. also check with barbarian motorsports i work there and we can get the street scene kit . the inferno orange you see on the fourms here is the barbarian motorsports company vehicle. you can see it in person at barbarian motorsports in riverside , ca.

[DON_RAFA]

very nice

[garcmol]

How does the Street Scene rear spoiler attach? 3M tape or drilling?

[SummoneR]

Originally Posted by garcmol

How does the Street Scene rear spoiler attach? 3M tape or drilling?

Based off the instructions from their site 3M tape for all pieces.
http://www.streetsceneeq.com/instruc.../950-70233.pdf



STREET SCENE EQUIPMENT,INC. 950-70233
365 McCormick Avenue CHEVY CAMARO
Costa Mesa, Ca. 92626 2010
Phone (714) 426-0590 Fax (714) 426-0591 REAR WING
3 PIECE SET URETHANE
INSTALLATION INSTRUCTIONS
NOTE: Fit all parts before painting ( See Special Instructions For Paint Prep. ) Parts that have been
installed, preped, or painted are not returnable.
NOTE:
Check fit all body parts PRIOR to paint. Follow urethane prep instructions before painting. Take
your time and pre-fit all pieces so that they will have a tight fit to the body.
VERY IMPORTANT ! Read and understand all directions and check the following parts list before starting
installation.
PARTS LIST
1 Rear Wing 1 Instruction Sheet 12 FT 1/2" Two Sided Tape # 75344
1 Urethane Prep Sheet 5PKGS 3M Adhesion Promoter
TOOL LIST
NONE REQUIRED
1. Remove any other wings if so installed.
2. Set the Street Scene center rear wing in place to see where the two sided tape will go. You will need to
clean both the vehicle and the new wing with 3M promoter so that the tape will stick good.
3. Do the same procedure to the left and right side of the wing. Clean with the 3M promoter.
Below is a photo where the two sided tape goes on the center wing and corners.
TAPE LINE ON CENTER WING
PAGE 1 09/24/09 SSE 950-70233
TAPE LINE ON CORNERS LEFT & RIGHT
4. Lift the corners of the tape backing on the ends. Do not pull all off at this time.
6. Set wing onto the deck lid where it will be installed. Grab the corner of the tape backing and pull. Apply
pressure to the wing. Do the same on all pieces.
PAGE 2

[garcmol]

Awesome thanks!

[CleanCutCreations]

I like this GFX kit! It looks aggressive and IMO much better than the factory style. We just installed a set on MARKBOLT's SS and other than re-engineering the way the side skirts attach to the pinchweld, the install was pretty straightforward. Don't get me wrong, there is alot of prep to do to this kit prior to install it is far from a "sand n paint" trial fit is a must. All in all, it is a nice kit. Go here for our install pics: http://www.flickr.com/photos/cccstl/...7622840193783/

[SSTony]

i just installed mine and i see way to much of the black rubber from underneath the door. i cant move it up any farther than it is

[SummoneR]

Originally Posted by CleanCutCreations

I like this GFX kit! It looks aggressive and IMO much better than the factory style. We just installed a set on MARKBOLT's SS and other than re-engineering the way the side skirts attach to the pinchweld, the install was pretty straightforward. Don't get me wrong, there is alot of prep to do to this kit prior to install it is far from a "sand n paint" trial fit is a must. All in all, it is a nice kit. Go here for our install pics: http://www.flickr.com/photos/cccstl/...7622840193783/

You do some clean work!! I wish you all were in California!! I am looking for a shop just like you. Everyone near me only does "Insurance" work, so I don't trust them to do any painting on my car, I am looking for someone who does custom work. I might have to take a trip to Missouri :-)

[SilverRain]

I just had my Street Scene side skirt and front chin splitter installed. Check out these pics

[YouEnvyMySS]

SWEET!!!!! Very clean! I LIKE it a LOT!!