Official 1/4 Mile (V6) 2010+ Camaro Fast List

[ROD1]

Originally Posted by 67 GTO

With visions of stretched chains and spun bearings dancing in my head, I headed to the track for one last time for the season.

Thanks to HDRS again for lending me his slicks.

Almost caught the big dog but very pleased with my times today. Might even give "Red Brick" a run for his money. LOL

1320'.......... 13.453
1320’ mph… 101.90

Grats man! Ya almost grabbed top spot! Pretty wild combo on that time vs. mph !?

[67 GTO]

Originally Posted by ROD1

Grats man! Ya almost grabbed top spot! Pretty wild combo on that time vs. mph !?

Thanks, made 5 passes all very consisistent, 3 best below. I'm in love with slicks.

[bmorecam]

Originally Posted by KMPrenger

Congrats Dan! That is a fantastic number!

Makes me feel confident that with slicks I could hit 13's as well considering the only other mods you have is the shorties and pulley...

...well maybe I should say I feel the car could do it in good DA....I'm not sure if this driver can do it or not though lol.

By the way...anyone here use the Torque app? It uses GPS and OBDII readings to measure its numbers (not an accelerometer). Wish I knew how accurate it really is.

I know my first run would have been under 6 seconds if only I hadn't spun so much. If you pay attention you'll see the car actually turn left from spinning the first time so I had to let out a bit.

What interface are you using with torque and where did you buy it from? Yours look like there's no lag. Did you datalog to CSV file yet? Anyway you can post up a log?

67GTO, You are definitely on the roll

[KMPrenger]

Originally Posted by bmorecam

What interface are you using with torque and where did you buy it from? Yours look like there's no lag. Did you datalog to CSV file yet? Anyway you can post up a log?...

I'm using a cheap ol' ELM 327 version 1.4 bluetooth adapter. There is basically very little lag...I will say that it seems like some monitors...for instance the MPH monitor might start off a bit slow but then it catches up rather quickly, but I see no pausing in my data. I try not to run too many monitors at once, which should help keep the lag to a minimum.

I wasn't datalogging during these runs, but I did do a datalog while driving a backroad. Haven't looked at it yet though.

[bmorecam]

Where did you get your elm327 from? That is actually good compared to what I was experiencing with my elm. It didn't matter if I had 1 or 7 PID's open, it would lag like crazy. Are you getting any error messages on your torque app? If so, how much are you getting? Mine would go into 100's in no time.

[KMPrenger]

Originally Posted by bmorecam

Where did you get your elm327 from? That is actually good compared to what I was experiencing with my elm. It didn't matter if I had 1 or 7 PID's open, it would lag like crazy. Are you getting any error messages on your torque app? If so, how much are you getting? Mine would go into 100's in no time.

I bought it on ebay from a seller called Interfuse I believe. I actually haven't taken a look at the OBD-II status screen because it seems to be working well enough that I wasn't worried about errors. Looks like it only shows you if it has any errors while it is connected up, so I'll try to remember to take a look at that next time and get back with you.

I took a quick look at my log file. Wasn't a whole lot to look at...plus I hadn't really set up the logging to log the PID's I'd really like to see, so I just set that up. Again, I'll try to get a decent log in the future and get back to you

[usa1camaro1969]

Originally Posted by 67 GTO

Thanks, made 5 passes all very consisistent, 3 best below. I'm in love with slicks.

Nice runs.

[bmorecam]

Thanks prenger.. torque is an awesome app when it works! It look like you got lucky. The vid you posted look great. I didn't even know you can do the parameter overlay with the video..nice!

Forgot to add.. when you log, log the rpm, KR, ignition timing, and throttle position.

[Glasstop2010RS]

Congrats on your new PB,....that's moving !
Guess I'm going to need a tune and lose some weight to come close.
Great Run Dan, see you guys in the early spring ! Regards, Bob.

[67 GTO]

Originally Posted by Glasstop2010RS

Congrats on your new PB,....that's moving !
Guess I'm going to need a tune and lose some weight to come close.
Great Run Dan, see you guys in the early spring ! Regards, Bob.

Thanks Bob. Atco opens in Feb & sometimes in late Jan if the weather cooperates. Hope to see you then.

In the mean time I'll be prepping to take the top spot from that fellow in NY.

[rtcat600man]

And the challenge has been laid down. Now I want you two to have a clean fight. New swerving, no red lighten, and certainly no spray-in when this is a N/A run only. Now go to your respective lanes and light em up and come out hot and clean.

[KMPrenger]

Originally Posted by 67 GTO

Thanks Bob. Atco opens in Feb & sometimes in late Jan if the weather cooperates. Hope to see you then.

In the mean time I'll be prepping to take the top spot from that fellow in NY.

Awesome.

[ROD1]

Originally Posted by 67 GTO

Thanks Bob. Atco opens in Feb & sometimes in late Jan if the weather cooperates. Hope to see you then.

In the mean time I'll be prepping to take the top spot from that fellow in NY.

Heh! come get the little bunny!!!

[Can't_C_Me]

Can someone update this with Gretchen's last two 12sec runs?!