Strut clearance question - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

burna · 01-21-2021, 06:15 PM

Hey Guys,

So I'm looking to do a new 20x10 staggered setup.
Suspension's stock although I may do the BMR 1" lowers.

Question is can I run
20x10 ET35 285/40/20 front and
20x10 ET25 285/40/20 rear

without getting into any rubbing or fitment issues?

burna · 01-25-2021, 11:07 AM

Bump, please help!
I'm thinking 285/35/20 now, but it's clearing the strut is what im worried about with +35et upfront on a 20x10

Avenging Orange · 01-25-2021, 04:33 PM

You'll be fine. But it needs to be reversed....+25 front and +35 rear.

fleebag · 01-25-2021, 06:35 PM

I run 20x10(35) tsw's square setup and have to use a 5mm spacer up front. This is lowered a little on BC coilovers as well. And I run 305/35 Hankook RS-3 up front.

burna · 01-25-2021, 08:37 PM

Mhhh wonder if I could do the 285 upfront with +35 without the spacer. Reason being I'd like the rear wheels to stick out (just a bit) more than the front. (I dig the staggered look)

01-21-2021, 06:15 PM	#1
burna Drives: 2010 Camaro V6 LT Join Date: Jan 2021 Location: Toronto Posts: 12	Strut clearance question Hey Guys, So I'm looking to do a new 20x10 staggered setup. Suspension's stock although I may do the BMR 1" lowers. Question is can I run 20x10 ET35 285/40/20 front and 20x10 ET25 285/40/20 rear without getting into any rubbing or fitment issues? Attached Images Last edited by burna; 01-25-2021 at 11:07 AM.

01-25-2021, 04:33 PM	#3
Avenging Orange Drives: 2010 Inferno Orange 2SS/RS Join Date: Apr 2010 Location: Clermont, IN Posts: 3,297	You'll be fine. But it needs to be reversed....+25 front and +35 rear. __________________ 2010 Inferno Orange 2SS/RS M6 Black Leather, Sun Roof, OBX Headers, Borla touring axle back, Cold Air Inductions CAI , non synthetic fluids, BMR total bushing upgrade/1" lowering springs, DSE 32mm rear sway bar. GM fe4 shocks/struts/LCA's, AAM 3.91 diff, Vertini RFS1.8 20x9 +30. Conti ExtremeContact Sport 275/35/20. sjm autoprod ABL dash kit. Mike Norris tuned 413/419. Avenging Orange: 43 years of not buying into the Hype........and damn proud of it!! https://youtu.be/9JD9it6SmB8 https://youtu.be/xmelTlEzI34 KICKING CANCERS ASS SINCE 2015!!

01-25-2021, 11:07 AM	#2
burna Drives: 2010 Camaro V6 LT Join Date: Jan 2021 Location: Toronto Posts: 12	Bump, please help! I'm thinking 285/35/20 now, but it's clearing the strut is what im worried about with +35et upfront on a 20x10

01-25-2021, 06:35 PM	#4
fleebag Drives: Moneypit Join Date: Nov 2013 Location: Jax FL Posts: 163	I run 20x10(35) tsw's square setup and have to use a 5mm spacer up front. This is lowered a little on BC coilovers as well. And I run 305/35 Hankook RS-3 up front.

01-25-2021, 08:37 PM	#5
burna Drives: 2010 Camaro V6 LT Join Date: Jan 2021 Location: Toronto Posts: 12	Mhhh wonder if I could do the 285 upfront with +35 without the spacer. Reason being I'd like the rear wheels to stick out (just a bit) more than the front. (I dig the staggered look)