03-02-2019, 01:23 PM | #2381 |
'It's an experiment'
Drives: [COTW 2/09/15] '11 GPI LSA SC Z/LE Join Date: May 2014
Location: Dallas TX
Posts: 8,694
|
those look great!
Yea, the converter would help a bunch! Low idle stuff was just a clean up... -Don
__________________
747 RWHP 794 RWTQ
"Horsepower sells cars, torque wins races." - Enzo Ferrari See My Build: http://www.camaro5.com/forums/showthread.php?t=385577 |
03-03-2019, 10:48 PM | #2382 |
'It's an experiment'
Drives: [COTW 2/09/15] '11 GPI LSA SC Z/LE Join Date: May 2014
Location: Dallas TX
Posts: 8,694
|
6L80 with 6L90 torque converter - GPI Rebuild (cont.)
Just wanted to show the area's Ryan updated my tune for the new trans build and what he touched:
Some timing/air flow changes and a 'few' trans/pressure changes! -Don
__________________
747 RWHP 794 RWTQ
"Horsepower sells cars, torque wins races." - Enzo Ferrari See My Build: http://www.camaro5.com/forums/showthread.php?t=385577 Last edited by hammdo; 03-05-2019 at 12:24 PM. |
03-06-2019, 05:27 PM | #2383 | |
'It's an experiment'
Drives: [COTW 2/09/15] '11 GPI LSA SC Z/LE Join Date: May 2014
Location: Dallas TX
Posts: 8,694
|
Front Rear Control Arms Fixed
Today, the control arms finally came in -- I ordered the ones for the Z/28 -- but I'll show you what they are ;o)
Anyway, if you follow this guide, you'll see what you need to do and use: So, here are the tools I used: Brass BFH: 21mm tools, 10mm wrench, Torque Wrench/Ratched: Z/28 arms: Now, notice the part numbers on the arms: Yep, #'s on the arms are the same for my '11 2SS and the '14 Z/28 -- go figure Anyway, here is the progression: Loosen nut on the joint, and the arm bolt/nut, then wack this area with the BFH: Now, side by side look and you'll see, she's bent: Installed and torqued (I did raise the knuckle up so as to simulate load): Rinse/repeat on the other side (and of course, I had to pound more on that side to get the arm off -- yep figures)... Not bad and fairly quick job -- nice distraction for now ;o) -Don
__________________
747 RWHP 794 RWTQ
"Horsepower sells cars, torque wins races." - Enzo Ferrari See My Build: http://www.camaro5.com/forums/showthread.php?t=385577 |
|
03-06-2019, 06:13 PM | #2384 |
CamaroFans.com
|
Ha ha.. love the BFH. Glad you got fixed up.
|
03-06-2019, 06:29 PM | #2385 |
'It's an experiment'
Drives: [COTW 2/09/15] '11 GPI LSA SC Z/LE Join Date: May 2014
Location: Dallas TX
Posts: 8,694
|
On jack stands, limited ‘swing’ space ;o). Brass is less destructive to the knuckle. Glad it’s fixed also...
Always something on this money pit... -Don
__________________
747 RWHP 794 RWTQ
"Horsepower sells cars, torque wins races." - Enzo Ferrari See My Build: http://www.camaro5.com/forums/showthread.php?t=385577 |
03-06-2019, 06:46 PM | #2386 |
ZL1 Pilot
|
Air hammer that thing with a brass fitting
Lol
__________________
GP Tuning 2.5 Cam, RPS Carbon Twin Clutch, Ported Blower, Kook's Headers, Cold Air Inductions CAI, ID850's, 9.17 Lower, 2.5 Upper, JMS BAP, Pedders Front Radius Arm Inserts, Whiteline Subframe Inserts, Tuned by me with HP Tuners Idle Clip Link...........https://www.youtube.com/watch?v=gTL8S9eHwbs |
03-06-2019, 06:50 PM | #2387 |
'It's an experiment'
Drives: [COTW 2/09/15] '11 GPI LSA SC Z/LE Join Date: May 2014
Location: Dallas TX
Posts: 8,694
|
I do have one but, she popped pretty quickly...
Besides, it’s more fun to beat the sh** out of something once in a while ;op.. -Don
__________________
747 RWHP 794 RWTQ
"Horsepower sells cars, torque wins races." - Enzo Ferrari See My Build: http://www.camaro5.com/forums/showthread.php?t=385577 |
03-06-2019, 07:10 PM | #2388 |
ZL1 Pilot
|
Lmao!
__________________
GP Tuning 2.5 Cam, RPS Carbon Twin Clutch, Ported Blower, Kook's Headers, Cold Air Inductions CAI, ID850's, 9.17 Lower, 2.5 Upper, JMS BAP, Pedders Front Radius Arm Inserts, Whiteline Subframe Inserts, Tuned by me with HP Tuners Idle Clip Link...........https://www.youtube.com/watch?v=gTL8S9eHwbs |
03-06-2019, 09:21 PM | #2389 |
'It's an experiment'
Drives: [COTW 2/09/15] '11 GPI LSA SC Z/LE Join Date: May 2014
Location: Dallas TX
Posts: 8,694
|
Yep, that’s my ‘toxic’ masculinity at work...
;o) -Don
__________________
747 RWHP 794 RWTQ
"Horsepower sells cars, torque wins races." - Enzo Ferrari See My Build: http://www.camaro5.com/forums/showthread.php?t=385577 |
03-07-2019, 09:19 AM | #2390 |
Geoff
Drives: 2020 ZL1 Green Join Date: May 2013
Location: Houston
Posts: 1,720
|
The castings are the same, the difference is the bushing........
__________________
|
03-07-2019, 08:39 PM | #2391 |
'It's an experiment'
Drives: [COTW 2/09/15] '11 GPI LSA SC Z/LE Join Date: May 2014
Location: Dallas TX
Posts: 8,694
|
Hoping so. Didn't see much of a difference in the bushings though..
-Don
__________________
747 RWHP 794 RWTQ
"Horsepower sells cars, torque wins races." - Enzo Ferrari See My Build: http://www.camaro5.com/forums/showthread.php?t=385577 |
03-09-2019, 04:39 PM | #2392 | |
'It's an experiment'
Drives: [COTW 2/09/15] '11 GPI LSA SC Z/LE Join Date: May 2014
Location: Dallas TX
Posts: 8,694
|
Well, defibrillator/pacemaker was install on Thursday so recovering.
If your curious: Did get to take the car out Wednesday night. Felt solid — still need to tweak the alignment but, holds true and no issues. Hope to get to drive it next week so I can get the alignment done... Gonna be a while until I can race again... -Don
__________________
747 RWHP 794 RWTQ
"Horsepower sells cars, torque wins races." - Enzo Ferrari See My Build: http://www.camaro5.com/forums/showthread.php?t=385577 |
|
03-09-2019, 09:36 PM | #2393 |
Geoff
Drives: 2020 ZL1 Green Join Date: May 2013
Location: Houston
Posts: 1,720
|
Recover well and swiftly mate!
__________________
|
03-09-2019, 10:16 PM | #2394 |
'It's an experiment'
Drives: [COTW 2/09/15] '11 GPI LSA SC Z/LE Join Date: May 2014
Location: Dallas TX
Posts: 8,694
|
Thanks! Waiting is the hardest part :o)...
Nothing like carrying a cellphone in your chest 24/7... -Don
__________________
747 RWHP 794 RWTQ
"Horsepower sells cars, torque wins races." - Enzo Ferrari See My Build: http://www.camaro5.com/forums/showthread.php?t=385577 |
|
|
|
|