10-21-2012, 07:32 PM | #1 |
|
BMR lowering springs installed on '11 SS
Finished up the BMR 1" suspension drop! I love the new stance, and I haven't noticed a difference in the ride quality!!
__________________
1 7/8" TSP headers straight piped, Custom Tick Performance cam w/ supporting mods, 1" BMR springs and other BMR suspension mods. Tuned with HPtuners by Matt@FSP
|
10-21-2012, 07:45 PM | #2 |
Drives: 2000 Camaro SS Join Date: Feb 2010
Location: Louisville, Ky.
Posts: 25,179
|
Looks great!
|
10-21-2012, 07:52 PM | #3 |
Who's Laughing Now?
Drives: 2011 Camaro 1SS RS LS3 Summit White Join Date: May 2011
Location: Maryland
Posts: 322
|
Looks good man! I did mine this weekend too
|
10-21-2012, 08:31 PM | #4 |
|
Thanks guys!
__________________
1 7/8" TSP headers straight piped, Custom Tick Performance cam w/ supporting mods, 1" BMR springs and other BMR suspension mods. Tuned with HPtuners by Matt@FSP
|
10-21-2012, 09:01 PM | #5 |
Snark snark snark
Drives: RX350 Join Date: Sep 2008
Location: 3L Hell
Posts: 555
|
That looks a lot lower than 1".
__________________
What is this, CorvetteForum Lite?
|
10-21-2012, 09:08 PM | #6 |
|
I never measured it but that's the kit I bought ill have to measure it out and check for sure
__________________
1 7/8" TSP headers straight piped, Custom Tick Performance cam w/ supporting mods, 1" BMR springs and other BMR suspension mods. Tuned with HPtuners by Matt@FSP
|
10-21-2012, 09:48 PM | #7 |
Pull up Cougar!
Drives: 2016 2SS Join Date: Jul 2011
Location: San Diego
Posts: 2,875
|
|
10-22-2012, 09:23 AM | #8 |
Drives: Race Car Join Date: Sep 2009
Location: Seffner, FL
Posts: 6,226
|
Your car looks great!
I am sure with the shadowing and the car being black it looks a touch lower than the 1" lowering springs normally are but I bet if he took some measurements they would be spot on. |
10-28-2012, 02:08 AM | #9 |
|
so i forgot to get back to you guys but i was wondering what are the measurements that i should be seeing, i forgot to get a measurement before i started on the installation! But i love the ride its amazing how great the ride still is. Also here is another picture, a bit better.
__________________
1 7/8" TSP headers straight piped, Custom Tick Performance cam w/ supporting mods, 1" BMR springs and other BMR suspension mods. Tuned with HPtuners by Matt@FSP
|
10-29-2012, 10:08 AM | #10 | |
Drives: Race Car Join Date: Sep 2009
Location: Seffner, FL
Posts: 6,226
|
Quote:
Last edited by BMR Sales; 10-29-2012 at 10:36 AM. |
|
10-29-2012, 10:36 AM | #11 |
Drives: Race Car Join Date: Sep 2009
Location: Seffner, FL
Posts: 6,226
|
You should see measurements right around 29.75"-30" from the ground through the center of the wheel to the top of the front fenders and rear quarter panels. There is a little range there because every car is a little different and measurements will generally vary by 1/8" give or take a little.
|
|
|
|
|