05-14-2013, 01:22 PM | #29 |
Drives: Silver 1LT 2011 camaro Join Date: Jul 2011
Location: Decatur, Alabama and Troy, Alabama
Posts: 1,846
|
Sure is! I'm moving to troy in the fall so ill only be about an hour and a half away from PCB so hopefully i'll get to go to some Florida events
__________________
Last edited by SIM Curly; 05-14-2013 at 01:33 PM. |
05-14-2013, 01:28 PM | #30 |
Emerald Coast Camaros
Drives: A lot of show, not much go. Join Date: Mar 2011
Location: Emerald Coast
Posts: 3,388
|
Yeah, ECC has meet and greets/cruises monthly and they're from Tallahassee to Pensacola and everywhere in between.
|
05-14-2013, 01:30 PM | #31 |
Drives: Silver 1LT 2011 camaro Join Date: Jul 2011
Location: Decatur, Alabama and Troy, Alabama
Posts: 1,846
|
Im sure I could join a few
__________________
|
05-14-2013, 01:32 PM | #32 |
Emerald Coast Camaros
Drives: 2010 Camaro 2LT/RS M6 Join Date: Nov 2009
Location: Tallahassee FL
Posts: 9,687
|
|
05-14-2013, 01:33 PM | #33 |
Drives: Silver 1LT 2011 camaro Join Date: Jul 2011
Location: Decatur, Alabama and Troy, Alabama
Posts: 1,846
|
Oops just noticed the typo I'm moving to Troy, AL
__________________
|
05-14-2013, 01:41 PM | #34 |
Emerald Coast Camaros
Drives: 2010 Camaro 2LT/RS M6 Join Date: Nov 2009
Location: Tallahassee FL
Posts: 9,687
|
|
05-14-2013, 01:43 PM | #35 |
Drives: Silver 1LT 2011 camaro Join Date: Jul 2011
Location: Decatur, Alabama and Troy, Alabama
Posts: 1,846
|
I'd be down!
__________________
|
05-14-2013, 01:44 PM | #36 |
Drives: Really Slow Join Date: Apr 2010
Location: PA
Posts: 56,957
|
my mom lives in Holt.
__________________
|
05-14-2013, 01:45 PM | #37 |
Emerald Coast Camaros
Drives: A lot of show, not much go. Join Date: Mar 2011
Location: Emerald Coast
Posts: 3,388
|
What "special" tools would be required to DIY the headers that you think I probably wouldn't have...if any?
|
05-14-2013, 01:47 PM | #38 | |
Drives: Silver 1LT 2011 camaro Join Date: Jul 2011
Location: Decatur, Alabama and Troy, Alabama
Posts: 1,846
|
Quote:
11mm, 13mm, 15mm and 9/16" deep sockets with ratchet 9/16" open-end wrench 7/8" open-end wrench or 7/8" O2 sensor socket Small torque wrench (18 ft-lbs range) large zip-ties or bailing wire, small zip-ties Anti-seize thread compound Sawzall reciprocating saw Auto lift, or approx 2 foot tall jackstands or ramps
__________________
|
|
05-14-2013, 01:51 PM | #39 |
Drives: '15 Z06, '01 NBM SS, '97 SS Join Date: May 2009
Location: Rio Rancho, NM
Posts: 12,170
|
If the BBK's fit anything like the OBXs Id charge $300 to install em....lol
No really, they should be no more than a $200 affair brotha. Them folks up at XXX in PCola do em but I don't know what they'd charge on the V6ers. I think one of the SS Guys paid $180 when I was there. Can't wait to see LT's on your beast finally.... Ivan @ Southwest Speed |
05-14-2013, 01:53 PM | #40 | |
Drives: Silver 1LT 2011 camaro Join Date: Jul 2011
Location: Decatur, Alabama and Troy, Alabama
Posts: 1,846
|
Quote:
__________________
|
|
05-14-2013, 02:01 PM | #41 | |
Emerald Coast Camaros
Drives: A lot of show, not much go. Join Date: Mar 2011
Location: Emerald Coast
Posts: 3,388
|
Quote:
Dang, Ivan...I'd take them over there if I could get them on for $180....or even $200! That's a steal compared to what I was quoted. Maybe I'll call them up just to find out. |
|
05-14-2013, 02:02 PM | #42 |
it's mind bottling..
Drives: SGM Join Date: Apr 2011
Location: miami floirda.
Posts: 5,393
|
Try to do it man.
__________________
|
|
|
|
|