01-06-2015, 03:54 PM | #1 |
Probably tired right now
Drives: 1Lap1LE | EV6 FE | 18 F150 Join Date: Sep 2010
Location: At the office (CLT, NC)
Posts: 1,133
|
Greg Good ported LS3 heads - NEW, uninstalled, COMPLETE with upgraded springs, etc
SOLD
Last edited by RideZX6R; 02-12-2015 at 03:04 PM. |
01-06-2015, 07:25 PM | #2 |
Drives: 2010 Camaro SS Join Date: Dec 2006
Location: MN
Posts: 1,172
|
What is the improvement on CFM as compared to stock from this porting?
|
01-06-2015, 10:57 PM | #3 |
Probably tired right now
Drives: 1Lap1LE | EV6 FE | 18 F150 Join Date: Sep 2010
Location: At the office (CLT, NC)
Posts: 1,133
|
|
01-07-2015, 12:49 AM | #4 |
Drives: 2015 Summit White 2SS 1LE Join Date: Feb 2012
Location: Vance Alabama
Posts: 8,019
|
If they were ported by Greg I wouldn't be too concerned about the #s.
__________________
Retired wanna be cylinder head porter
2015 2SS 1LE Clutch reservoir, Vararam DRX, ported TB, TSP 2" headers, MGW shifter Totalled: 2010 1SS Wilkes Performance/Eagle 416 shortblock, TSP custom valvetrain, PRC 260 heads, Edelbrock Pro Flo 102, th400 swap, 8" PTC 5500 stall= 535/435 at the wheels tuned Gen 3 Performance and Dyno 10.97 @ 124 full weight in 3100 DA CamaroFest X |
01-07-2015, 09:46 AM | #5 |
Drives: 2010 Camaro 2SS/RS Join Date: Aug 2012
Location: Cordova, TN
Posts: 774
|
About how much rwhp over stock would this make?
__________________
2010 Camaro 2SS M6
2" Stainless Power Longtube Headers 3" Full exhaust w/ Off-Road H-Pipe Bo White Ported Throttle Body Hurst Short Throw Shifter Best Time: 12.43 @ 114, 1.99 60' on stock wheels and stock tires Build Thread |
01-07-2015, 11:44 PM | #6 | |
Probably tired right now
Drives: 1Lap1LE | EV6 FE | 18 F150 Join Date: Sep 2010
Location: At the office (CLT, NC)
Posts: 1,133
|
Quote:
He's very well known in the Viper and LS communities Depends on other mods honestly. 20-40whp on N/A car, perhaps more with a blower. |
|
01-08-2015, 10:41 AM | #7 |
|
May be interested. Have the heads been milled ?? Would be interested in swapping my low mileage LS3 heads. PM me.
Ed M.
__________________
RJT 2SS/RS, AAM 3.70's, MTI Sway Bars, Shifter & SS brake lines, ZLI calipers, rotors & pads, BMR Trailing & Toe Arms, rear cradle & diff bushes, Pedders XA's, Camber/Toe eccentrics, Radius arm inserts, GTO clutch reservoir, LS9 cam, Comp valve springs, Melling 10296 oil pump, CR5 timing chain, LS6 damper, CAI Cold Air Intake, ARH LT headers w/HF cats, GMPP touring axle back, Elite Engineering Catch Can, Forgeline 20x9.5 & 20x11 DS3 whls, 275/40/20 & 315/35/20 tires, 2011 Convertible spoiler, 1LE front spoiler, Lloyd "SS" Floor Mats, GM Camaro Trunk Mat, wrapped console & Grant steering wheel.
|
01-08-2015, 01:35 PM | #8 |
Probably tired right now
Drives: 1Lap1LE | EV6 FE | 18 F150 Join Date: Sep 2010
Location: At the office (CLT, NC)
Posts: 1,133
|
Sent a PM.
Thanks |
01-08-2015, 01:59 PM | #9 |
Drives: 14 Camaro 1LE,328i, and some Hondas Join Date: May 2014
Location: Virginia
Posts: 799
|
Stock powdered valve guides?
__________________
14' Camaro 1LE - Now self-tuned
FRH ported heads, Cam Motion LL solid roller, Jesel rockers, Morel lifters, Kooks headers, Corsa exhaust, ADM intake, Stock compression/bore/stroke 551whp 504wtq |
01-08-2015, 04:25 PM | #10 |
Probably tired right now
Drives: 1Lap1LE | EV6 FE | 18 F150 Join Date: Sep 2010
Location: At the office (CLT, NC)
Posts: 1,133
|
|
01-09-2015, 01:12 PM | #11 |
Probably tired right now
Drives: 1Lap1LE | EV6 FE | 18 F150 Join Date: Sep 2010
Location: At the office (CLT, NC)
Posts: 1,133
|
bump
|
01-12-2015, 03:33 PM | #12 |
Probably tired right now
Drives: 1Lap1LE | EV6 FE | 18 F150 Join Date: Sep 2010
Location: At the office (CLT, NC)
Posts: 1,133
|
updated info
|
01-13-2015, 12:42 PM | #13 |
Probably tired right now
Drives: 1Lap1LE | EV6 FE | 18 F150 Join Date: Sep 2010
Location: At the office (CLT, NC)
Posts: 1,133
|
bump!
|
02-04-2015, 01:34 AM | #14 |
Probably tired right now
Drives: 1Lap1LE | EV6 FE | 18 F150 Join Date: Sep 2010
Location: At the office (CLT, NC)
Posts: 1,133
|
top!
|
|
|
|
|