ADM FPCM - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

SSKyle · 03-24-2013, 03:39 PM

Can anyone post up a link for the fpcm for the ZL1 pump? I can't find it on their site.
Thanks

2012REDSS · 03-24-2013, 04:41 PM

Pm or call Andy. Great product. It does the trick and the data log will prove it

Adadda · 03-24-2013, 05:09 PM

http://admperformance.com/categories...29&category=69

Right on their site

Iam Broke · 03-24-2013, 05:14 PM

Ya, he added it a few weeks ago.

SSKyle · 03-24-2013, 05:58 PM

Thanks a lot.
How hard was it to get to the fpcm? I know you have to remove the back seat and the side panel, but other than that is it pretty a straight forward install?

ToddB · 03-24-2013, 06:09 PM

Easy as pie.

2012REDSS · 03-24-2013, 06:49 PM

Yep removing the seat was the hardest part

Scourage · 03-24-2013, 09:58 PM

I did it without removing the seat, just pulled the rear pass side panel back far enough to swap it out, wasn't too tough.

StreetSS · 03-25-2013, 06:46 AM

Removing the rear seat is fairly easy as well, if you choose to go that route. It is not necessary to remove any bolts. Pull up on the front of the lower seat to unclip and unhook at the back by pushing down where the hooks are (located maybe a foot from either side). To remove the top part of the seat, pull it down as if you are trying to accesss the trunk and use the latches at either side to release the seat back from the tubular mount and pull up. There are DIYs on here with pics if needed.

03-24-2013, 03:39 PM	#1
SSKyle Drives: 2011 SS/RS Join Date: Apr 2011 Location: Kentucky Posts: 47	ADM FPCM Can anyone post up a link for the fpcm for the ZL1 pump? I can't find it on their site. Thanks

03-24-2013, 05:14 PM	#4
Iam Broke PHAT B33 Drives: 2012 TF3 Camaro 2SS/RS M6 Join Date: Jun 2012 Location: Dark of the Moon Posts: 1,460 View My Garage	Ya, he added it a few weeks ago. __________________ Another 1 of 371 '12 T3 LS3 M6's built.

03-24-2013, 04:41 PM	#2
2012REDSS Drives: 2012 Camaro SS Join Date: Oct 2011 Location: NC Posts: 657	Pm or call Andy. Great product. It does the trick and the data log will prove it

03-24-2013, 05:09 PM	#3
Adadda Drives: 2012 Camaro SS. L99 Join Date: Nov 2012 Location: Panama City FL Posts: 113	http://admperformance.com/categories...29&category=69 Right on their site

03-24-2013, 05:58 PM	#5
SSKyle Drives: 2011 SS/RS Join Date: Apr 2011 Location: Kentucky Posts: 47	Thanks a lot. How hard was it to get to the fpcm? I know you have to remove the back seat and the side panel, but other than that is it pretty a straight forward install?

03-24-2013, 06:09 PM	#6
ToddB Drives: 2011 2SS Convertible Supercharged Join Date: Nov 2010 Location: WI Cert Welder Navy NSSN Posts: 1,157	Easy as pie.

03-24-2013, 06:49 PM	#7
2012REDSS Drives: 2012 Camaro SS Join Date: Oct 2011 Location: NC Posts: 657	Yep removing the seat was the hardest part

03-24-2013, 09:58 PM	#8
Scourage Syntax Error Drives: 2010 Camaro 2SS/RS Join Date: Jan 2009 Location: SE Nebraska Posts: 557 View My Garage	I did it without removing the seat, just pulled the rear pass side panel back far enough to swap it out, wasn't too tough.

03-25-2013, 06:46 AM	#9
StreetSS Drives: 2011 Camaro SS Join Date: Jan 2013 Location: VA Posts: 160 View My Garage	Removing the rear seat is fairly easy as well, if you choose to go that route. It is not necessary to remove any bolts. Pull up on the front of the lower seat to unclip and unhook at the back by pushing down where the hooks are (located maybe a foot from either side). To remove the top part of the seat, pull it down as if you are trying to accesss the trunk and use the latches at either side to release the seat back from the tubular mount and pull up. There are DIYs on here with pics if needed.