03-17-2014, 11:04 AM | #71 |
Drives: 2014 Red Rock 2SS 1LE RS NPP Join Date: Mar 2014
Location: Hudson Valley New York
Posts: 246
|
Would it make sense to remove the 2 front seat to give you more room to work? I know it is extra work but might make moving around back there easier.
|
04-28-2014, 05:47 PM | #72 |
Account Suspended
Drives: 2010 2SS/RS Join Date: Jun 2009
Location: Texas
Posts: 3,418
|
Thank you, this write up helped me a lot.
Does anyone have tips for the small screw by back window? It was the worst trying to get it out, i cant imagine putting it back in Last edited by flyer08; 04-28-2014 at 06:44 PM. |
04-28-2014, 08:11 PM | #73 |
Drives: 2010 Camaro 2SS/RS RJT, 6speed Join Date: May 2011
Location: South Florida
Posts: 887
|
I used a tiny ratchet and small socket. Using both hands... Holding the socket on that bolt. It's a pain at that angle.
__________________
2010 Camaro 2SS/RS, LS3 - 6 speed. Mods, Magnaflow exhaust with resonator delete. ******** 12" stealth box subwoofer kit, Kicker 400 mono amp, JL XD 400/4 amp.
Last edited by Camaroshark; 04-29-2014 at 03:01 PM. |
04-28-2014, 10:31 PM | #74 |
Account Suspended
Drives: 2010 2SS/RS Join Date: Jun 2009
Location: Texas
Posts: 3,418
|
I think to put it back in ill need another set of small hands. Thanks for ideas
|
06-05-2015, 11:05 AM | #75 |
Drives: 2017 2SS Hyper Blue Join Date: Apr 2009
Location: North Port,Florida
Posts: 517
|
Universal adapter for ratchet wrench helped me
__________________
Mods-Corsa Extreme Axleback
|
06-05-2015, 12:43 PM | #76 | |
Drives: 2017 2SS Hyper Blue Join Date: Apr 2009
Location: North Port,Florida
Posts: 517
|
Quote:
__________________
Mods-Corsa Extreme Axleback
|
|
08-30-2015, 12:56 PM | #77 |
Drives: 2020 2SS 1LE M6 Join Date: Jun 2014
Location: St. Louis, MO
Posts: 86
|
Great thread op, subscribed
__________________
2020 Camaro 2SS 1LE M6 Rally Green
|
02-08-2016, 07:08 PM | #78 |
|
Great DIY, helped out a lot. Just thought I would add one thing. One of my speakers were blown, so I gutted it and was able to use the factory bracket with my new speakers. Turned out real solid.
Sent from my SM-G900V using Tapatalk
__________________
CAI intake | OBX LT Headers | Flowmaster AT Exhaust | Trifecta Tune | SS Rear Diff, Axles & Driveshaft Zex 100 Shot Nitrous | Konig Airstrike Wheels | Custom Engine Cover, Fuse Box & Underhood Bowtie Eibach Springs & SS Sway Bars | BMR Strut Brace | Drake Shifter | Vitesse Paddles | 13.26 @ 105.88 mph |
02-08-2016, 10:41 PM | #79 |
Drives: 20’ Chevrolet Camaro 2SS 1LE Join Date: Jan 2009
Location: San Diego
Posts: 1,577
|
Looks good. Did you replace all 4 speakers and amp also?
__________________
|
02-09-2016, 09:06 AM | #80 |
H-Town Camaro Club
Drives: 2013 Dusk Edition 2SS/M6/Sun/NPP Join Date: May 2014
Location: Houston
Posts: 2,234
|
|
02-09-2016, 04:39 PM | #81 |
|
No, just replacing the 6x9s for now. May do the doors in the future.
Sent from my SM-G900V using Tapatalk
__________________
CAI intake | OBX LT Headers | Flowmaster AT Exhaust | Trifecta Tune | SS Rear Diff, Axles & Driveshaft Zex 100 Shot Nitrous | Konig Airstrike Wheels | Custom Engine Cover, Fuse Box & Underhood Bowtie Eibach Springs & SS Sway Bars | BMR Strut Brace | Drake Shifter | Vitesse Paddles | 13.26 @ 105.88 mph |
02-09-2016, 07:12 PM | #82 |
Drives: 20’ Chevrolet Camaro 2SS 1LE Join Date: Jan 2009
Location: San Diego
Posts: 1,577
|
Ok, cool. The front doors are way easier.
__________________
|
09-15-2016, 07:08 PM | #83 |
|
I know this is an oldie but a goodie.
I pulled this up because I am pulling the rear speakers out tomorrow and found this thread. I'm not sure why everyone is taking so much time to pull everything apart and then reinstall the speakers the same way, only to have to do it again later down the road. I am going to install mine from underside in the trunk area so its just a few screws to remove when I want to remove or add rear speakers.
__________________
Car mods: never enough!
|
09-15-2016, 07:30 PM | #84 |
H-Town Camaro Club
Drives: 2013 Dusk Edition 2SS/M6/Sun/NPP Join Date: May 2014
Location: Houston
Posts: 2,234
|
Some do. Unless you put a mic in the car to SQ spec it, the only downside is you losing an inch or three of trunk space. Your primary issue is you have to take the car apart to reach them before you can remove the OEM ones. The seats and back dash go in and out easy enough, it's just time.
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
DIY : Install headers on 2010 Camaro SS | Nine Ball | Camaro DIY & HOW-TO instructions & discussions | 70 | 06-25-2020 06:40 PM |
My JL 12" and JL 250 amp install VIDEO AND PIX! | TAG UR IT | Audio, Video, Bluetooth, Navigation, Radar, Electronics Forum | 55 | 02-12-2011 01:03 AM |
Please help with speaker install!! | camaro10rs | Audio, Video, Bluetooth, Navigation, Radar, Electronics Forum | 0 | 03-13-2010 12:32 AM |
DIY : Install catback on 2010 Camaro SS | Nine Ball | Camaro DIY & HOW-TO instructions & discussions | 3 | 08-09-2009 04:36 PM |