Where does this part go? - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

MR.Sarge · 06-10-2017, 04:06 PM

So today I did the ZL1 Sideskirts on my 1LE and when taking off the driver side, I found this part in the Driver side rocker stock PN: 92212989 - Camaro Fender Front Insulator is what it says it is looking it up. It was inside the rocker and I have NO idea where it goes or where it came from. Passenger side didnt have it (it was tucked in the front corner of the driver side rocker)

Does anyone know exactly where this part goes? I am stumped and cant figure it out, looked at the diagram on newgmparts.com and it doesn't specify where its from. Any and all help appreciated guys, thanks!

18LTLoveIt · 06-10-2017, 04:11 PM

Another too close pics post.... :(

DvKillar · 06-10-2017, 04:21 PM

Camaro Fender Front Insulator
sounds like it is a part that fits inside the fender-to-skirt to seal from weather?

Cyber10 · 06-10-2017, 04:32 PM

Sits underneath fender, you have to take the fender off of the car to put it on.

edit: here's a pic of one of them when my car was torn apart

DvKillar · 06-10-2017, 04:46 PM

Dang! that wasn't seated very well to fall that far!

MR.Sarge · 06-10-2017, 05:20 PM

Quote:

Originally Posted by Cyber10

Sits underneath fender, you have to take the fender off of the car to put it on.

edit: here's a pic of one of them when my car was torn apart

Thanks for the pic Cyber10! That helps a LOT! I will try to do it myself but i might have dealer do it since its still under warranty.

Cyber10 · 06-10-2017, 05:24 PM

Quote:

Originally Posted by MR.Sarge

Thanks for the pic Cyber10! That helps a LOT! I will try to do it myself but i might have dealer do it since its still under warranty.

I'd take it to a dealer if it's under warranty, it's a pain in the ass to do as you have to remove the front bumper and I believe loosen the front of the rocker moulding in order to get the fender off. Can't remember 100% as it was a few months ago since I did it but pretty sure that's what needs done. A lot of work just to put that thing back in place imo.

06-10-2017, 04:06 PM	#1
MR.Sarge Drives: 2015 2SS/RS 1LE Join Date: Nov 2011 Location: Windsor, ON Posts: 511 View My Garage	Where does this part go? So today I did the ZL1 Sideskirts on my 1LE and when taking off the driver side, I found this part in the Driver side rocker stock PN: 92212989 - Camaro Fender Front Insulator is what it says it is looking it up. It was inside the rocker and I have NO idea where it goes or where it came from. Passenger side didnt have it (it was tucked in the front corner of the driver side rocker) Does anyone know exactly where this part goes? I am stumped and cant figure it out, looked at the diagram on newgmparts.com and it doesn't specify where its from. Any and all help appreciated guys, thanks! Attached Images __________________

06-10-2017, 04:32 PM	#4
Cyber10 Drives: 2010 Camaro 2SS/RS Join Date: Mar 2016 Location: Indianapolis Posts: 288	Sits underneath fender, you have to take the fender off of the car to put it on. edit: here's a pic of one of them when my car was torn apart __________________ 491 hp/438 tq LS3 Conversion \| Comp Cam Custom Grind \| Mast Heads \| Comp Cam Push Rods \| LS7 Timing Chain \| 180 Thermostat \| Ported Intake \| Ported TB \| SLP UDP \| K & N CAI \| Custom 3800 Stall Converter \| Aluminum 1 Piece Driveshaft \| Kooks 1 7/8" LTH \| High Flow Cats \| ARH 3" Exhaust \| ARH Mufflers \| Eibach Lowering Springs \| BMR Floor Brace Subframe Connectors with Tunnel Brace \| BMR Moly Lower Rear Control Arms \| Oracle LED Halo Kit

06-10-2017, 04:11 PM	#2
18LTLoveIt Drives: 2018 Hyper Blue LT RS Join Date: Dec 2016 Location: Phoenix AZ Posts: 1,474 View My Garage	Another too close pics post.... :(

06-10-2017, 04:21 PM	#3
DvKillar Drives: 2015 Chevy Camaro 2LS Join Date: May 2017 Location: MWC, OK Posts: 815	Camaro Fender Front Insulator sounds like it is a part that fits inside the fender-to-skirt to seal from weather?

06-10-2017, 04:46 PM	#5
DvKillar Drives: 2015 Chevy Camaro 2LS Join Date: May 2017 Location: MWC, OK Posts: 815	Dang! that wasn't seated very well to fall that far!