Oil Pan removal - looking for suggestions - Page 4 - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

CFD · 12-27-2015, 07:57 AM

Quote:

Originally Posted by Soybeanrice

Got any extra sets of flanges CFD? I'll take your work on the frame integrity...I even tried lifting the engine a couple inches by the tranny and still couldnt get it off... the damn ac lines and battery, along with the crossmember make it impossibru

There's a handful of guys on here who have installed the flanges and none have had any problems. It is structurally sound as long as the flanges fit nicely and the welding is good. There's a procedure that I used when installing them to insure proper fitment. I'm building a new motor for my car so with the engine out I will take a couple of pictures and do a little write up if anyone is interested.

lionssfan · 04-17-2018, 09:24 PM

Quote:

Originally Posted by CFD

There's a handful of guys on here who have installed the flanges and none have had any problems. It is structurally sound as long as the flanges fit nicely and the welding is good. There's a procedure that I used when installing them to insure proper fitment. I'm building a new motor for my car so with the engine out I will take a couple of pictures and do a little write up if anyone is interested.

do you still have flanges for this crossmember removal. anyone else have these thanks

CFD · 04-18-2018, 05:21 AM

Quote:

Originally Posted by lionssfan

do you still have flanges for this crossmember removal. anyone else have these thanks

I do still make the flanges and have some in stock.

AG1LE · 04-18-2018, 08:54 AM

Quote:

Originally Posted by CFD

I do still make the flanges and have some in stock.

Do you install?

gsxrturbo · 04-18-2018, 06:38 PM

I used his flang kit,worked great,Iam a welder and fab guy though

mmaattppllaayy · 04-19-2018, 09:32 AM

I used his flanges on my car as well. Work perfect and only take 30minutes to install as long as you have a welder. The only issue I ran into is when I went twin turbo the passenger side flange had to have the back portion cut off to clear some of the charge pipes.

Painter · 07-26-2019, 09:51 AM

Quote:

Originally Posted by CFD

I do still make the flanges and have some in stock.

Sir I would like to buy a set of flanges for the cross member, how do we get together, thanks Al workman

Nb1081 · 07-27-2019, 05:40 AM

I tried buying these flanges a while ago and cfd disappeared on me after i asked for paypal info? But im still interested in a set.

ez$ · 12-21-2021, 08:52 AM

im interested in this kit. how do i go about setting up purchase?

07-27-2019, 05:40 AM	#50
Nb1081 Drives: 10 2ss/rs Join Date: Jul 2018 Location: Shelby ny Posts: 436	I tried buying these flanges a while ago and cfd disappeared on me after i asked for paypal info? But im still interested in a set. __________________ [/SIGPIC]10 2ss ls3 sw long tubes,cai intake,phastek scoop,se3" exhaust,elite e2, bw stg2tb, tsp f35, motive 4.10 lpw cover, 15" conversion, 510whp tuned by john donovan

04-18-2018, 06:38 PM	#47
gsxrturbo Drives: 2010 ss Join Date: Oct 2015 Location: windom mn Posts: 337	I used his flang kit,worked great,Iam a welder and fab guy though

04-19-2018, 09:32 AM	#48
mmaattppllaayy Drives: '10 Camaro 2SS Join Date: Jul 2013 Location: Charlotte, NC Posts: 428	I used his flanges on my car as well. Work perfect and only take 30minutes to install as long as you have a welder. The only issue I ran into is when I went twin turbo the passenger side flange had to have the back portion cut off to clear some of the charge pipes.

12-21-2021, 08:52 AM	#51
ez$ Drives: 2010 camaro ss Join Date: Dec 2021 Location: houston tx Posts: 1	im interested in this kit. how do i go about setting up purchase?