[Purplt1]

Originally Posted by dethzombi

Has anyone taken the time to make these prettier? I know I could just purchase a corvette cover and call it a day, but I don't want my engine saying "Corvette" Might have to see if I can find someone to make something for the car to cover the manifold and make it a little prettier.

I shaved mine. I think I put a pic in this post. Didn't like the corvette cover

[6spdhyperblue]

Originally Posted by Purplt1

I shaved mine. I think I put a pic in this post. Didn't like the corvette cover

You did a great job on that. Certainly a lot more work!

[arkamaross]

does anyone know if you can fit a 103mm tb to a ported lt2 manifold?

[ButcherSS]

OP, did you shorten the pipe coming into the opening?

[Kngofharts13]

Originally Posted by Dvs510

Already posted about this.. the gm strut brace litteraly sits on top of the lt2 manifold and that’s without the cover. So tight u can’t slide a piece of paper between.. so yes it technically fits.. but the movement of the motor under load can possibly put too much pressure on the manifold.. I had a welder notch out my strut brace and weld more back inside to reinforce what he did

Thank you, after seeing it shaved on top I may take that route and then have nothing to worry about with the brace.

[Kngofharts13]

Originally Posted by Purplt1

Yes the 95mm does work.

What did you use to fill in the four holes? I was thinking about attempting what you accomplished but I can tell there’s a lot more then grinding and sanding.

[Purplt1]

Originally Posted by Kngofharts13

What did you use to fill in the four holes? I was thinking about attempting what you accomplished but I can tell there’s a lot more then grinding and sanding.

I used epoxy then body filler. . I'm working on another gloss black lt2 over the weekend

[MackSteelPrivateEye]

So you are probably pulling about 500hp at the crank instead of 455 now if you gained 30 RWHP.

[Dvs510]

Originally Posted by BlackbeastSS2

I am getting the corvette cover but I will somehow get rid of the corvette lettering with some type of overlay with Camaro. A few have talked about this already so somebody might come up with the solution.

I hit up emblempros and they said there already working on a direct fit overlay sticker/emblem that will make it say Camaro instead of corvette.. not sure when it will b out but might b worth the wait

[BlackbeastSS2]

Originally Posted by Dvs510

I hit up emblempros and they said there already working on a direct fit overlay sticker/emblem that will make it say Camaro instead of corvette.. not sure when it will b out but might b worth the wait

Thanks for the info much appreciated.

[OB0001]

Originally Posted by Dvs510

I hit up emblempros and they said there already working on a direct fit overlay sticker/emblem that will make it say Camaro instead of corvette.. not sure when it will b out but might b worth the wait

Nice

[SlyStyle]

I've installed the lt2 intake now, too. With the Lt1 intake was on full load lambda 0.82-0.83. Now 0.78 ! Does the tune have to be changed or why is that?

[6spdhyperblue]

Likely because the throttle body placement changed relative to the air box, the intake hose is clocked on a different angle and is drawing air differently across the MAF. Also, you could be pulling deeper into the MAF curve and it needs to get rescaled to stay in that window.

Should be easy enough to trim that back in line

[BlackbeastSS2]

Originally Posted by Dvs510

I hit up emblempros and they said there already working on a direct fit overlay sticker/emblem that will make it say Camaro instead of corvette.. not sure when it will b out but might b worth the wait

I just peeled off the Corvette lettering with a heat gun and replaced it with some wrap for now. I will add their sticker emblem depending on their design.