Check Your 1.4" BMR Springs - Page 2 - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

c_LoW29 · 01-02-2013, 10:41 AM

Nothing has been done to resolve this issue, I have marked this one down as a live and learn experience guess I will have to changed the electrical tape periodically to keep the spings from making noise when they rub. The issue isnt a big deal a little bit of coil dampner would probably fix this but I refuse to pay for it out of my pocket due to a design flaw. Every other spring I have seen that is made by big name companies like Eibach, PFADT, ect. has coil dampner material to eleviate this issue.

c_LoW29 · 04-17-2013, 02:34 PM

So its been a while and ofcourse no response BMR has horrible customer service I have not been offered a resolution just money back for my alignment. Horrible company to work with never found a solution or responded with one like they said they where going to. Soon I will be trashing these springs once I get some coilovers.

BMR IS A JOKE !!!!

BBQdDude · 04-17-2013, 02:56 PM

OP, what does the noise sound like?

c_LoW29 · 04-17-2013, 02:59 PM

the noise is the two dead springs hitting eachother. You can see by where the springs rub in the pictures above. I covered it with some electrical tape and all noise was gone. But that isnt a suitable fix and shouldnt need to be done.

gnturboray · 04-17-2013, 03:02 PM

I've had the same springs for 2 years and no problems. BMR has always been helpful when I've called them. I know they post here so I would send them a PM about it and if they don't respond start a BMR bashing thread which will surely draw their attention.

c_LoW29 · 04-17-2013, 05:46 PM

That's what this thread has turned into actually I have spoke to them via PM and on the phone. They simply state that "our technicians are looking into it" for 9 months they have been looking into it.

01-02-2013, 10:41 AM	#15
c_LoW29 Drives: 2011 2SS/RS, 2010 Mustang GT Join Date: May 2010 Location: Slidell, LA Posts: 2,412 View My Garage	Nothing has been done to resolve this issue, I have marked this one down as a live and learn experience guess I will have to changed the electrical tape periodically to keep the spings from making noise when they rub. The issue isnt a big deal a little bit of coil dampner would probably fix this but I refuse to pay for it out of my pocket due to a design flaw. Every other spring I have seen that is made by big name companies like Eibach, PFADT, ect. has coil dampner material to eleviate this issue.

04-17-2013, 02:34 PM	#16
c_LoW29 Drives: 2011 2SS/RS, 2010 Mustang GT Join Date: May 2010 Location: Slidell, LA Posts: 2,412 View My Garage	So its been a while and ofcourse no response BMR has horrible customer service I have not been offered a resolution just money back for my alignment. Horrible company to work with never found a solution or responded with one like they said they where going to. Soon I will be trashing these springs once I get some coilovers. BMR IS A JOKE !!!!

04-17-2013, 02:56 PM	#17
BBQdDude Drives: 2010 Chevy Camaro 2SS RS Join Date: Jun 2011 Location: Columbus, Oh Posts: 347	OP, what does the noise sound like?

04-17-2013, 02:59 PM	#18
c_LoW29 Drives: 2011 2SS/RS, 2010 Mustang GT Join Date: May 2010 Location: Slidell, LA Posts: 2,412 View My Garage	the noise is the two dead springs hitting eachother. You can see by where the springs rub in the pictures above. I covered it with some electrical tape and all noise was gone. But that isnt a suitable fix and shouldnt need to be done.

04-17-2013, 03:02 PM	#19
gnturboray Drives: SIM 2010 2SS/RS LS3 LPE750 Join Date: Feb 2012 Location: Mckinney, Texas Posts: 764	I've had the same springs for 2 years and no problems. BMR has always been helpful when I've called them. I know they post here so I would send them a PM about it and if they don't respond start a BMR bashing thread which will surely draw their attention.

04-17-2013, 05:46 PM	#20
c_LoW29 Drives: 2011 2SS/RS, 2010 Mustang GT Join Date: May 2010 Location: Slidell, LA Posts: 2,412 View My Garage	That's what this thread has turned into actually I have spoke to them via PM and on the phone. They simply state that "our technicians are looking into it" for 9 months they have been looking into it.