Clutch Slave Interchangeability - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

SSjosh · 11-07-2016, 06:06 PM

I have searched low, I have searched high, can't seem to find what i'm looking for. 2010 SS bolt-on, stock clutch, 28k miles. I must have been through every throw out and slave thread in this place.

My slave isn't even bad but the throw out is. I'd buy just a bearing if I could? and throw in a speed bleeder and monster bushing.

On Gmpartsdirect, PN 19210297 (M10) is discontinued.

Is there any difference with PN 24266013 (MM6) or the ZL1 PN 24249220? I.E. will they fit?

Rockauto has a centric replacement for 2010-2011 but not anything 2013+ that I saw, but if there is a different design within gm (that lasts longer), I might choose an o.e. replacement.

Can any of you guys positively clear this up for me?

Thanks

camguynj · 11-07-2016, 06:21 PM

Check out this thread Correct Slave Cylinder for LS3 http://www.camaro5.com/forums/showthread.php?t=427258

SSjosh · 11-07-2016, 06:43 PM

I know that 19210297 is the correct one. However, wondering if the others are interchangeable, better design, better bearing?

I'm half tempted to find just a bearing once I get the slave out unless someone else has done the leg work on the dimensions.

camguynj · 11-07-2016, 08:26 PM

Quote:

Originally Posted by SSjosh

I know that 19210297 is the correct one. However, wondering if the others are interchangeable, better design, better bearing?

I'm half tempted to find just a bearing once I get the slave out unless someone else has done the leg work on the dimensions.

Monster has one and you can have them pre-install their Billet Release Bearing Support

https://monsterclutches.com/monster-...g-support.html

camguynj · 10-31-2020, 08:42 AM

NEW from Tilton...self adjusting throw out bearing with braided SS lines with adapters for Camaro Tremec6060. The braided SS bleed line eliminates the need for a separate remote bleed line

https://tiltonracing.com/product/cam...ease-bearings/

Racer41 · 06-06-2023, 10:48 AM

Quote:

Originally Posted by SSjosh

I know that 19210297 is the correct one. However, wondering if the others are interchangeable, better design, better bearing?

I'm half tempted to find just a bearing once I get the slave out unless someone else has done the leg work on the dimensions.

Josh, did you ever figure out the difference between these slave cylinders? I am im the same boat now wondering if one is better because I just blew mine out and would like to put the best one in that I can.

camguynj · 06-08-2023, 02:26 AM

Quote:

Originally Posted by Racer41

Josh, did you ever figure out the difference between these slave cylinders? I am im the same boat now wondering if one is better because I just blew mine out and would like to put the best one in that I can.

Doubt you’re going to hear from him, he hasn’t been on the forum in 5 yrs. If you really want the best check out the Tilton slave in post 5

11-07-2016, 06:06 PM	#1
SSjosh Drives: 2011 SS 6MT Join Date: Jun 2015 Location: Gulf Coast Posts: 31	Clutch Slave Interchangeability I have searched low, I have searched high, can't seem to find what i'm looking for. 2010 SS bolt-on, stock clutch, 28k miles. I must have been through every throw out and slave thread in this place. My slave isn't even bad but the throw out is. I'd buy just a bearing if I could? and throw in a speed bleeder and monster bushing. On Gmpartsdirect, PN 19210297 (M10) is discontinued. Is there any difference with PN 24266013 (MM6) or the ZL1 PN 24249220? I.E. will they fit? Rockauto has a centric replacement for 2010-2011 but not anything 2013+ that I saw, but if there is a different design within gm (that lasts longer), I might choose an o.e. replacement. Can any of you guys positively clear this up for me? Thanks

10-31-2020, 08:42 AM	#5
camguynj Drives: '13 SS/RS LS3 BRM Cammed NPP Join Date: Jan 2013 Location: NJ Posts: 3,812 View My Garage	NEW from Tilton...self adjusting throw out bearing with braided SS lines with adapters for Camaro Tremec6060. The braided SS bleed line eliminates the need for a separate remote bleed line https://tiltonracing.com/product/cam...ease-bearings/ Last edited by camguynj; 08-31-2022 at 07:55 PM.

11-07-2016, 06:21 PM	#2
camguynj Drives: '13 SS/RS LS3 BRM Cammed NPP Join Date: Jan 2013 Location: NJ Posts: 3,812 View My Garage	Check out this thread Correct Slave Cylinder for LS3 http://www.camaro5.com/forums/showthread.php?t=427258

11-07-2016, 06:43 PM	#3
SSjosh Drives: 2011 SS 6MT Join Date: Jun 2015 Location: Gulf Coast Posts: 31	I know that 19210297 is the correct one. However, wondering if the others are interchangeable, better design, better bearing? I'm half tempted to find just a bearing once I get the slave out unless someone else has done the leg work on the dimensions.