Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com
 
Bigwormgraphix
Go Back   Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com > Engine | Drivetrain | Powertrain Technical Discussions > V8 and V6 Transmissions / Driveline (6L80 / 6L50 / TR6060 / AY6)


Reply
 
Thread Tools
Old 11-07-2016, 06:06 PM   #1
SSjosh
 
SSjosh's Avatar
 
Drives: 2011 SS 6MT
Join Date: Jun 2015
Location: Gulf Coast
Posts: 31
Clutch Slave Interchangeability

I have searched low, I have searched high, can't seem to find what i'm looking for. 2010 SS bolt-on, stock clutch, 28k miles. I must have been through every throw out and slave thread in this place.

My slave isn't even bad but the throw out is. I'd buy just a bearing if I could? and throw in a speed bleeder and monster bushing.

On Gmpartsdirect, PN 19210297 (M10) is discontinued.

Is there any difference with PN 24266013 (MM6) or the ZL1 PN 24249220? I.E. will they fit?

Rockauto has a centric replacement for 2010-2011 but not anything 2013+ that I saw, but if there is a different design within gm (that lasts longer), I might choose an o.e. replacement.

Can any of you guys positively clear this up for me?

Thanks
SSjosh is offline   Reply With Quote
Old 11-07-2016, 06:21 PM   #2
camguynj


 
camguynj's Avatar
 
Drives: '13 SS/RS LS3 NPP BRM
Join Date: Jan 2013
Location: NJ
Posts: 3,237
Check out this thread Correct Slave Cylinder for LS3 http://www.camaro5.com/forums/showthread.php?t=427258
camguynj is online now   Reply With Quote
Old 11-07-2016, 06:43 PM   #3
SSjosh
 
SSjosh's Avatar
 
Drives: 2011 SS 6MT
Join Date: Jun 2015
Location: Gulf Coast
Posts: 31
I know that 19210297 is the correct one. However, wondering if the others are interchangeable, better design, better bearing?

I'm half tempted to find just a bearing once I get the slave out unless someone else has done the leg work on the dimensions.
SSjosh is offline   Reply With Quote
Old 11-07-2016, 08:26 PM   #4
camguynj


 
camguynj's Avatar
 
Drives: '13 SS/RS LS3 NPP BRM
Join Date: Jan 2013
Location: NJ
Posts: 3,237
Quote:
Originally Posted by SSjosh View Post
I know that 19210297 is the correct one. However, wondering if the others are interchangeable, better design, better bearing?

I'm half tempted to find just a bearing once I get the slave out unless someone else has done the leg work on the dimensions.
Monster has one and you can have them pre-install their Billet Release Bearing Support http://monsterclutches.com/gen-5-cam...slave-cylinder
camguynj is online now   Reply With Quote
Old 10-31-2020, 08:42 AM   #5
camguynj


 
camguynj's Avatar
 
Drives: '13 SS/RS LS3 NPP BRM
Join Date: Jan 2013
Location: NJ
Posts: 3,237
NEW from Tilton...self adjusting throw out bearing with braided SS lines with adapters for Camaro Tremec6060. The braided SS bleed line eliminates the need for a separate remote bleed line

https://www.tickperformance.com/tilt...owout-bearing/

Last edited by camguynj; 10-31-2020 at 08:54 AM.
camguynj is online now   Reply With Quote
 
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:58 PM.


Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2021, vBulletin Solutions, Inc.