11-02-2019, 06:59 AM | #407 | |
Drives: 12 camaro ss, 72 chevelle, 91camaro Join Date: Dec 2013
Location: findlay,oh
Posts: 2,069
|
Quote:
I dont log backpressure per say but I use dome pressure to figure that out. Drive pressure is right around 1.6:1 at the 31 psi mark. Which isn't bad at all
__________________
12 camaro ss 427lsx, th400, f310 heads, crower shaft mounts, gpi specd solid roller, shearerfab 2k hp a/w, twin bullseye 88mm turbos, hughes pro ssx bolt together converter, holley dominator, 8.50 cert, backhalf, Ford 9", 33x17x16 tires, c16 fuel
|
|
11-02-2019, 02:51 PM | #408 |
Drives: 12 camaro ss, 72 chevelle, 91camaro Join Date: Dec 2013
Location: findlay,oh
Posts: 2,069
|
Here's pics of the limiters. Plenty of adjustment left either way. Just finished the other side.
__________________
12 camaro ss 427lsx, th400, f310 heads, crower shaft mounts, gpi specd solid roller, shearerfab 2k hp a/w, twin bullseye 88mm turbos, hughes pro ssx bolt together converter, holley dominator, 8.50 cert, backhalf, Ford 9", 33x17x16 tires, c16 fuel
|
11-02-2019, 10:00 PM | #409 |
Drives: 12 camaro ss, 72 chevelle, 91camaro Join Date: Dec 2013
Location: findlay,oh
Posts: 2,069
|
Got the diaper all on. Theres 6 straps that hold it on total. 2 on each side, and 2 on the front. Along with a velcro strap to hold it tight to the pan by the flexplate.
I'm a little concerned with how close it is to the flexplate. But I haven't tried to start it yet with it in place.
__________________
12 camaro ss 427lsx, th400, f310 heads, crower shaft mounts, gpi specd solid roller, shearerfab 2k hp a/w, twin bullseye 88mm turbos, hughes pro ssx bolt together converter, holley dominator, 8.50 cert, backhalf, Ford 9", 33x17x16 tires, c16 fuel
|
11-08-2019, 11:12 AM | #410 |
Drives: 12 camaro ss, 72 chevelle, 91camaro Join Date: Dec 2013
Location: findlay,oh
Posts: 2,069
|
Heard back from the machine shop about the ls2 block I dropped off. Block was already punched. 005 over. Bores looked good so he suggested just put a fresh crosshatch in the bore and sending it. Will be picking that up, getting some main studs, filling it. Then taking it back to make sure the bore didn't distort and for the line bore.
Tomorrow is the track rental. Should have done awesome air being the high is 37 degrees. Worked ok the tune some more and pulled some fuel out of after start and warmup enrichment. Starts way better cold now. Scaled tune down to make room for 325 kpa(32.6psi) praying it holds together for me and the limiters pan out. Will report back tomorrow
__________________
12 camaro ss 427lsx, th400, f310 heads, crower shaft mounts, gpi specd solid roller, shearerfab 2k hp a/w, twin bullseye 88mm turbos, hughes pro ssx bolt together converter, holley dominator, 8.50 cert, backhalf, Ford 9", 33x17x16 tires, c16 fuel
|
11-09-2019, 06:56 PM | #411 |
Drives: 12 camaro ss, 72 chevelle, 91camaro Join Date: Dec 2013
Location: findlay,oh
Posts: 2,069
|
Well she didnt like the extra boost and -1195 DA. Let go around the 600 foot area. Got it home, pulled all the plugs, they look fine, no oil in the coolant, no coolant in the oil. Thinking it just straight up snapped a rod. Will pull apart the next few days
__________________
12 camaro ss 427lsx, th400, f310 heads, crower shaft mounts, gpi specd solid roller, shearerfab 2k hp a/w, twin bullseye 88mm turbos, hughes pro ssx bolt together converter, holley dominator, 8.50 cert, backhalf, Ford 9", 33x17x16 tires, c16 fuel
Last edited by ttshovel; 11-09-2019 at 08:05 PM. |
11-11-2019, 03:59 PM | #412 |
Drives: 12 camaro ss, 72 chevelle, 91camaro Join Date: Dec 2013
Location: findlay,oh
Posts: 2,069
|
Got it pulled and couldn't find anything wrong with it. Gonna throw it back in and see wtf it is. I jumped the gun by not doing a compression check first. Thinking now that by tripping overboost protection, it left something triggered in the ecm. Gonna throw it back in and get it started. Then pull it back out and start the new build
__________________
12 camaro ss 427lsx, th400, f310 heads, crower shaft mounts, gpi specd solid roller, shearerfab 2k hp a/w, twin bullseye 88mm turbos, hughes pro ssx bolt together converter, holley dominator, 8.50 cert, backhalf, Ford 9", 33x17x16 tires, c16 fuel
|
11-11-2019, 09:48 PM | #413 |
Drives: Never just fly under the radar Join Date: Jul 2015
Location: Kansas
Posts: 1,531
|
Sux to do all the extra work but in the end seems like fairly good news!
Will be watching for your winter build.
__________________
1-8-4-3-6-5-7-2
Old Skool |
11-14-2019, 03:23 PM | #414 | |
Drives: 12 camaro ss, 72 chevelle, 91camaro Join Date: Dec 2013
Location: findlay,oh
Posts: 2,069
|
Quote:
Haven't finished buttoning it up yet. Ordered a jegs brand mid plate and motion raceworks front plate with the cutouts for turbo manifolds. Hoping it clears the manifolds! Really dont wanna redo the hotside. Decided I'm going to leave this 6.0 in it for a while and do the rest of the safety stuff, clean up all the wiring,, and add the boost leash for better boost control over this pid control in ms3. Looking to get this thing started back up this weekend
__________________
12 camaro ss 427lsx, th400, f310 heads, crower shaft mounts, gpi specd solid roller, shearerfab 2k hp a/w, twin bullseye 88mm turbos, hughes pro ssx bolt together converter, holley dominator, 8.50 cert, backhalf, Ford 9", 33x17x16 tires, c16 fuel
|
|
11-17-2019, 09:31 PM | #415 |
Drives: 12 camaro ss, 72 chevelle, 91camaro Join Date: Dec 2013
Location: findlay,oh
Posts: 2,069
|
Got the thing to fire today. Pulled dash out. Found a tripped fuse for the crank/cam signal. Replaced it and it popped as soon as it had power to it. Traced it to a ground that had a bad connection. Recrimped it, threw a fuse in it, and it fired right up.
Since I'm going to a boost leash and no longer going to use the ms3 boost control. I moved the dome pressure sensor to the intake. Drilled a new hole in the front of the intake for it. It's an aem 5 bar so I should be good forever now. Will work on motorplating next. Thinking I am going to move the motor back after all.
__________________
12 camaro ss 427lsx, th400, f310 heads, crower shaft mounts, gpi specd solid roller, shearerfab 2k hp a/w, twin bullseye 88mm turbos, hughes pro ssx bolt together converter, holley dominator, 8.50 cert, backhalf, Ford 9", 33x17x16 tires, c16 fuel
|
11-18-2019, 03:07 AM | #416 |
|
That turbo is just insane. Glad you didn't hurt the motor after all, really impressive it's holding together. Ill have to make it down there to MCR next year to check this thing out in person. Almost makes me want to gut mine....but not quite lol.
|
11-18-2019, 06:46 AM | #417 |
Drives: 12 camaro ss, 72 chevelle, 91camaro Join Date: Dec 2013
Location: findlay,oh
Posts: 2,069
|
Thanks! I'm gonna try to compete in their no preps next season so we will see how that goes!
__________________
12 camaro ss 427lsx, th400, f310 heads, crower shaft mounts, gpi specd solid roller, shearerfab 2k hp a/w, twin bullseye 88mm turbos, hughes pro ssx bolt together converter, holley dominator, 8.50 cert, backhalf, Ford 9", 33x17x16 tires, c16 fuel
|
11-19-2019, 11:31 AM | #418 | |
Captain Gingerbeard
Drives: 2012 IOM RS/SS 6MT Join Date: Feb 2013
Location: West Twin Cities, MN
Posts: 2,489
|
Hopefully you get on 1320 video!
__________________
Custom ordered 2012 6MT RS/SS on 11/25/2011. Picked up 01/31/12.
Pedders Coilovers, BMR trailing arms and toe-links, Prothane solid poly subframe bushings, JDP Motorsports rear upper control arm bushings, Texas Speed long-tube headers with 2" primaries, modified fully 3" Magnaflow competition catback. CAI cold-air intake. DBA rotors, Hawk pads. Quote:
|
|
11-19-2019, 05:12 PM | #419 |
Drives: 12 camaro ss, 72 chevelle, 91camaro Join Date: Dec 2013
Location: findlay,oh
Posts: 2,069
|
Thanks man. For sure I'll be on the street racing channel/ dnr auto. They are putting on the no preps I will be at!
Pulled the engine harness, gonna pull the trans and motor to cut the firewall. Right now I'm looking at setting it all back 5 inches but I may decide on more after it's all said and done.
__________________
12 camaro ss 427lsx, th400, f310 heads, crower shaft mounts, gpi specd solid roller, shearerfab 2k hp a/w, twin bullseye 88mm turbos, hughes pro ssx bolt together converter, holley dominator, 8.50 cert, backhalf, Ford 9", 33x17x16 tires, c16 fuel
Last edited by ttshovel; 11-19-2019 at 05:33 PM. |
11-21-2019, 06:51 PM | #420 |
Drives: 12 camaro ss, 72 chevelle, 91camaro Join Date: Dec 2013
Location: findlay,oh
Posts: 2,069
|
I've made the decision to sell my current turbo setup to start over. Will be keeping the turbo and mounting it up front and center. A local shop, just starting out, is cutting me a deal. I pay for materials and put their sticker in the back window and they will build the kit for free. No brainer there
__________________
12 camaro ss 427lsx, th400, f310 heads, crower shaft mounts, gpi specd solid roller, shearerfab 2k hp a/w, twin bullseye 88mm turbos, hughes pro ssx bolt together converter, holley dominator, 8.50 cert, backhalf, Ford 9", 33x17x16 tires, c16 fuel
|
|
|
|
|