2014 Heat extractor on a 2010 hood - Page 5 - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

Low RS · 03-25-2014, 09:03 PM

Quote:

Originally Posted by Jerry7297

Been working on that....

Here is attempt one, Fiberglass. It would still work I just dont want to put in all the time to bondo it and all that. so today...

2nd attempt. Lexan from Home Depot. This fits fine and I think I am just going to Plastidip it and be done with it...

CAN YOU GET US A PIC OF THIS ON THE SCOOP BEFORE YOU PAINT IT??

Jerry7297 · 03-25-2014, 10:16 PM

Quote:

Originally Posted by Low RS

CAN YOU GET US A PIC OF THIS ON THE SCOOP BEFORE YOU PAINT IT??

Nope done. Sorry about that. I will upload a pic tomorrow with the Hood liner on.

Dexter9522 · 03-25-2014, 11:18 PM

How did you make that, just heat gun and a break or did you use the fiberglass as a mold. Did you make a template as well. Very nice work

zkdreads · 03-26-2014, 06:58 AM

prepped and ready for surgery

Jerry7297 · 03-26-2014, 07:19 AM

Quote:

Originally Posted by Dexter9522

How did you make that, just heat gun and a break or did you use the fiberglass as a mold. Did you make a template as well. Very nice work

Lexan, dremel and and a torch or heat gun.

I did have a template I had made for the fiberglass piece I made. I used that cut it out and strategically bent the lexan over some angle on one of the trailers at work. the back corners are not sealed so I put silicone on them and plastidipped over. I am very pleased with it and it was a lot easier than the fiberglass.

I can upload a template with the measurments for it if anyone would like. The only bad thing is the front 2 mounting nuts were a PITA to get on.

Jerry7297 · 03-26-2014, 07:21 AM

Quote:

Originally Posted by zkdreads

prepped and ready for surgery

You dont have to leave the template on the car. If you are pleased with the placement just use a sharpie and mark it out and remove the template. Good luck man just triple check before you start cutting

zkdreads · 03-26-2014, 11:05 AM

Done!

spadz93 · 03-26-2014, 11:21 AM

man i wanna do this, but i'd be shitting bricks cutting into my hood

zkdreads · 03-26-2014, 11:25 AM

At worst u cut the hole to small. Then adjust it from there

Jerry7297 · 03-26-2014, 12:14 PM

Quote:

Originally Posted by zkdreads

Done!

Looks really good with your color combo.

Would like to see the underneath side...

Dexter9522 · 03-26-2014, 05:49 PM

Quote:

Originally Posted by Jerry7297

Lexan, dremel and and a torch or heat gun.

I did have a template I had made for the fiberglass piece I made. I used that cut it out and strategically bent the lexan over some angle on one of the trailers at work. the back corners are not sealed so I put silicone on them and plastidipped over. I am very pleased with it and it was a lot easier than the fiberglass.

I can upload a template with the measurments for it if anyone would like. The only bad thing is the front 2 mounting nuts were a PITA to get on.

That would be awesome.

Deftones · 03-26-2014, 06:07 PM

Does anyone have pics of how it mounts on the 2014?

Jerry7297 · 03-26-2014, 06:08 PM

Finished product. I will work on the template layout for this. Give me a little bit will get it done soon.

zkdreads · 03-27-2014, 08:01 AM

Quote:

Originally Posted by Deftones

Does anyone have pics of how it mounts on the 2014?

this wont work on the 2010-2013 model. the hood is a difference size with the indentions and the hood is made for the actual scoop. i tried yesterday. one of my camaro club members have a 2014. and you would have to play with your 2010 hood and scoop to possibly come up with something to how it would fit let alone stay there. on the 2014 the insulator is different because it has fastener holes as well for the hood scoop pan too

03-25-2014, 11:18 PM	#59
Dexter9522 Drives: SS Join Date: May 2013 Location: Az Posts: 273	How did you make that, just heat gun and a break or did you use the fiberglass as a mold. Did you make a template as well. Very nice work Last edited by Dexter9522; 03-26-2014 at 12:26 AM.

03-26-2014, 06:58 AM	#60
zkdreads Drives: 2010 Camaro LS V6 Join Date: Jul 2010 Location: Tampa, Florida Posts: 2,784	prepped and ready for surgery __________________ C-LO or Sonic "Without Struggle there is no progress" I am your best nightmare!

03-26-2014, 11:05 AM	#63
zkdreads Drives: 2010 Camaro LS V6 Join Date: Jul 2010 Location: Tampa, Florida Posts: 2,784	Done! Attached Images __________________ C-LO or Sonic "Without Struggle there is no progress" I am your best nightmare!

03-26-2014, 11:21 AM	#64
spadz93 BUMBL Z Drives: 2015 ZL1 Join Date: Nov 2013 Location: Northern NJ Posts: 2,573 View My Garage	man i wanna do this, but i'd be shitting bricks cutting into my hood __________________ Current: 2015 ZL1 M6, Rotofab Intake, LS3 throttle body, 2.55 Upper/9.17 Lower w/ Idler Relocation, DMS Reinforced Brick, ID1050X, 1 7/8" Headers, ProSpeed HX/Reservoir, DSX Aux Pump/Flex Fuel Sensor, E85, McLeod RXT, BMR 1" Drop, Tuned by Pat G Past: 2010 2SS, some bolt ons, 415rwhp/400rwtq

03-26-2014, 11:25 AM	#65
zkdreads Drives: 2010 Camaro LS V6 Join Date: Jul 2010 Location: Tampa, Florida Posts: 2,784	At worst u cut the hole to small. Then adjust it from there __________________ C-LO or Sonic "Without Struggle there is no progress" I am your best nightmare!

03-26-2014, 06:07 PM	#68
Deftones Drives: 2012 RS/SS LS3 Join Date: Jun 2012 Location: Bakersfield, CA Posts: 873	Does anyone have pics of how it mounts on the 2014? __________________

03-26-2014, 06:08 PM	#69
Jerry7297 Drives: 2018 2SS/ 1LE Join Date: Sep 2012 Location: San Marcos TX Posts: 710 View My Garage	Finished product. I will work on the template layout for this. Give me a little bit will get it done soon.