Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com
 
dave@hennessey
Go Back   Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com > General Camaro Forums > Camaro ZL1 Forum - ZL1 Specific Topics


Reply
 
Thread Tools
Old 09-23-2019, 12:56 PM   #1
Alqadif75
 
Drives: Zl1 2013
Join Date: Feb 2019
Location: Doha qatar
Posts: 8
Tvs2300

Dears I have 2013 automatic ZL1 Modified
102 throttle body
JLT Intake
Methanol kit
DSX External fuel pump
Heat exchanger
Headers
1050 injectors
416 strocker
10" crank pulley Currently i have 750rwhp at 14psi boost,
my target is to hit the 850rwhp or near to that,
Looking to get the TVS2300
What is the Required supercharger pulies for the tvs2300 , extra parts , required builts,.... that suits my setup in order to achieve my goal
Alqadif75 is offline   Reply With Quote
Old 09-24-2019, 01:37 PM   #2
1LEric
 
Drives: 2015 Camaro 1LE
Join Date: Jun 2016
Location: NJ
Posts: 152
850 can be done with the stock blower don’t waste your money on the TVs2300
1LEric is offline   Reply With Quote
Old 10-01-2019, 03:27 PM   #3
RyangAsh
 
Drives: 2014 ZL1
Join Date: Apr 2018
Location: KCMO
Posts: 178
Quote:
Originally Posted by Alqadif75 View Post
Dears I have 2013 automatic ZL1 Modified
102 throttle body
JLT Intake
Methanol kit
DSX External fuel pump
Heat exchanger
Headers
1050 injectors
416 strocker
10" crank pulley Currently i have 750rwhp at 14psi boost,
my target is to hit the 850rwhp or near to that,
Looking to get the TVS2300
What is the Required supercharger pulies for the tvs2300 , extra parts , required builts,.... that suits my setup in order to achieve my goal
If it has a stock upper, change that for a 2.5 or smaller depending on what you want to do and see where you are at...Heat will be the real battle.
RyangAsh is offline   Reply With Quote
Old 10-01-2019, 03:32 PM   #4
JB'sZL1

 
Drives: 2013 ZL1 and 2019 Ram Laramie
Join Date: May 2017
Location: Milwaukee
Posts: 1,102
Quote:
Originally Posted by RyangAsh View Post
If it has a stock upper, change that for a 2.5 or smaller depending on what you want to do and see where you are at...Heat will be the real battle.
A 10" and 2.55" will push the sc over 25k...not good.
JB'sZL1 is offline   Reply With Quote
Old 10-01-2019, 04:27 PM   #5
Little Walter
 
Drives: ZL1
Join Date: Dec 2016
Location: New Orleans
Posts: 129
You can do a 9.55 lower with a 2.55 upper being that you have a good heat exchanger, but based what you have if you convert to E85 you might see 80whp gain. Since this is an auto trannyr? At the end of the day go to a track and get your E.T. to know what the car is really doing. I use to play the dyno game from one dyno to another looking for a great number. Some dyno's read high and some are very stingy. If you have your stock baseline dyno before you did all of your work and then dyno after the upgrades on the same dyno will always let you know what you have really gained in horsepower. The clock at the track will always be consistent with you, I have seen as much as 80 hp difference from one dyno to another on just dyno jets alone and 133 hp lower on a mustang. Again the track clock and 60 ft will tell you the deal.
Little Walter is offline   Reply With Quote
Old 10-03-2019, 11:28 AM   #6
RyangAsh
 
Drives: 2014 ZL1
Join Date: Apr 2018
Location: KCMO
Posts: 178
Quote:
Originally Posted by JB'sZL1 View Post
A 10" and 2.55" will push the sc over 25k...not good.
Says who? A guy that's never done it?
RyangAsh is offline   Reply With Quote
Old 10-03-2019, 11:29 AM   #7
JB'sZL1

 
Drives: 2013 ZL1 and 2019 Ram Laramie
Join Date: May 2017
Location: Milwaukee
Posts: 1,102
Quote:
Originally Posted by RyangAsh View Post
Says who? A guy that's never done it?
That's your input?
JB'sZL1 is offline   Reply With Quote
Old 10-03-2019, 02:48 PM   #8
RyangAsh
 
Drives: 2014 ZL1
Join Date: Apr 2018
Location: KCMO
Posts: 178
Quote:
Originally Posted by JB'sZL1 View Post
That's your input?
My input is the rotational speed of the supercharger is usually looked down upon because of the heat production. If you keep it serviced and fresh bearing in it, it will last. TONS of guys doing it. Make sure your HX cooling system is as efficient as it can be and let the thing eat. Now, if you aren't prepared to do maintenance on the blower, maybe you don't spin it above 25k, but there's a lot to be had out of these blowers if you are prepared to take the necessary steps.
RyangAsh is offline   Reply With Quote
Old 10-09-2019, 10:46 PM   #9
FasNuf
 
FasNuf's Avatar
 
Drives: 2014 Camaro ZL1
Join Date: Jul 2019
Location: Salem Oregon
Posts: 588
Quote:
Originally Posted by RyangAsh View Post
Says who? A guy that's never done it?
Says Lingenfelter...check it.

https://www.lingenfelter.com/PRI2014...heet%201.1.pdf

FasNuf is offline   Reply With Quote
Old 10-18-2019, 05:48 AM   #10
BURNYs
BURN RUBBER NOT YOUR SOUL
 
BURNYs's Avatar
 
Drives: 2013 ZL1 M6 Blue Ray
Join Date: Jun 2017
Location: PA
Posts: 69
Stock blower can do it. Save money.
__________________
Mods-Kong Ported Blower, ID1700X injectors, 2.35/8.65, TSP Ported Heads, Custom Grind Cam, RPM 5 inch Intake, NW 102mm, Kooks 1 7/8, Corsa Extreme, Afco Heat Exchanger, PNR 4 gal ice tank/EMP pump, Oil catch can, Thermal reduction plates, BR7EF plugs, DSX Aux Pump, Monster LT1-S triple. 788hp/757tq-93, 839hp/785tq-E85. Burn Rubber Not Your Soul
BURNYs is offline   Reply With Quote
Old 11-09-2019, 10:59 AM   #11
CJ27
 
Drives: Chevrolet camaro zl1
Join Date: May 2019
Location: Tajas
Posts: 71
Quote:
Originally Posted by BURNYs View Post
Stock blower can do it. Save money.
I have the 2300. He speaks the truth don't waste your money.
__________________
2014 Sliver ZL1. Magnuson, SW long tubes, AFCO H/E, BTR Stage 2, flex fuel sensor, meth injection. 760rwhp e85. 680 on 93.
CJ27 is offline   Reply With Quote
Old 01-06-2020, 01:12 PM   #12
RyangAsh
 
Drives: 2014 ZL1
Join Date: Apr 2018
Location: KCMO
Posts: 178
Quote:
Originally Posted by FasNuf View Post
The guy in the post below yours is spinning his blower at 25,765 @ 7k rpm..and tons of guys are doing it in V's. Talk to any tuner, most will say max that baby out.
RyangAsh is offline   Reply With Quote
Old 01-06-2020, 01:36 PM   #13
JB'sZL1

 
Drives: 2013 ZL1 and 2019 Ram Laramie
Join Date: May 2017
Location: Milwaukee
Posts: 1,102
Quote:
Originally Posted by RyangAsh View Post
The guy in the post below yours is spinning his blower at 25,765 @ 7k rpm..and tons of guys are doing it in V's. Talk to any tuner, most will say max that baby out.
Tons? What...ten fatties? And it took you two months to formulate that thought?

I know what CVS guys have done to their LSA's. Do you know how many of them have replaced their blowers...or their engines?

If it's safe to regularly over rev the charger, why not tune it and over rev the engine as well? Not saying it can't be done, but at what cost? How long will the voodoo last at 8250 rpm? And how many will make it to 150k-200k miles if the regularly rev it to 8250?

Spew this crap over at MG6.
JB'sZL1 is offline   Reply With Quote
Old 01-06-2020, 02:13 PM   #14
tstodii
 
Drives: White 2015 Z/28
Join Date: Jul 2017
Location: Charleston SC
Posts: 208
The funny life lesson "just because you can, doesn't mean you should" can be found in this post. I happened to learn this particular lesson while working as an oil change monkey at a local dealership. I was emptying the oil drain caddy via it's fancy(read always breaking) pneumatic extractor running full tilt when a tech walked over asking why I had the pump running wide open? My response was it works faster that way and that's how hard the pump lets me run it. He simply looked at me and said his car runs a lot faster at 100% throttle but it's not gonna last as long as it would under normal conditions... I was 18 at the time and never really put 2 and 2 together before that. A few months after we all started using the machine at a lower speed, it still broke the same way as before hahahaha

Also, isn't more heat generated the faster you spin the supercharger? So at some point you'll be creating more heat that essentially robs the power instead of increasing it.

I'd think putting the 2300 on there and spinning it slower would generate less heat and be a lot better for the OPs location considering the brutal temps that Doha is known for.

OP, have you tried reaching out to a vendor or speed shop to see what they would recommend? Might be worth hitting up Ted, RPM or a few other sponsors to see what they have to say. Can't beat the experience those guys have with the 5th Gen and they will point you in the right direction to obtain your goals
tstodii is offline   Reply With Quote
 
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:25 PM.


Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2020, vBulletin Solutions, Inc.