09-20-2013, 12:18 AM | #1513 |
In The Circle
Drives: 2010 Camaro 2SSRS IOM M6 Join Date: May 2009
Location: Abbotsford BC Canada
Posts: 11,291
|
OUCH! Those BMR bushings were suppose to be almost as hard as aluminum ones.
__________________
|
09-20-2013, 03:04 AM | #1514 |
In The Circle
Drives: 2010 Camaro 2SSRS IOM M6 Join Date: May 2009
Location: Abbotsford BC Canada
Posts: 11,291
|
My goodies from DSS is now in Washington State. UPS is on time for a Sumas WA delivery tomorrow.
__________________
|
09-21-2013, 02:16 PM | #1515 |
In The Circle
Drives: 2010 Camaro 2SSRS IOM M6 Join Date: May 2009
Location: Abbotsford BC Canada
Posts: 11,291
|
Made good progress yesterday on Hammerhead but had to put project on hold due family emergency. Just have to put driveshaft in, check all bolt's for correct torque and put the wheels back on it. I'll try to post some pic's later to night.
__________________
|
09-22-2013, 07:38 AM | #1516 |
In The Circle
Drives: 2010 Camaro 2SSRS IOM M6 Join Date: May 2009
Location: Abbotsford BC Canada
Posts: 11,291
|
Here we go with part one of the 12 bolt Hammerhead install.
__________________
Last edited by Merc; 09-22-2013 at 07:58 AM. |
09-22-2013, 07:44 AM | #1517 |
In The Circle
Drives: 2010 Camaro 2SSRS IOM M6 Join Date: May 2009
Location: Abbotsford BC Canada
Posts: 11,291
|
This pic might be one of interest in regards to the diff vent. For the time being we slid a piece of tube inside the the vent fitting then slid the stock vent tube inside of it and used a piece of heat shrink tube to hold it all in place. This fix is temporary til I figure out what AN fittings and hose I want to use.
__________________
|
09-23-2013, 07:53 AM | #1518 |
In The Circle
Drives: 2010 Camaro 2SSRS IOM M6 Join Date: May 2009
Location: Abbotsford BC Canada
Posts: 11,291
|
Between my Buddy Bill and SCT we have been trying set up my laptop for data logging. It's been a struggle since my tunner was several firm ware updtes behind. Were close now just need one more driver for the automatic updater. Looks like one more call to SCT. There support has been stellar.
__________________
|
09-25-2013, 11:16 PM | #1519 | |
In The Circle
Drives: 2010 Camaro 2SSRS IOM M6 Join Date: May 2009
Location: Abbotsford BC Canada
Posts: 11,291
|
Just a little test on the hoist at 1500 rpm hardly hear it but it works.
__________________
|
|
09-25-2013, 11:19 PM | #1520 | |
In The Circle
Drives: 2010 Camaro 2SSRS IOM M6 Join Date: May 2009
Location: Abbotsford BC Canada
Posts: 11,291
|
On a roll today data logging is working now.
__________________
|
|
09-25-2013, 11:31 PM | #1521 |
In The Circle
Drives: 2010 Camaro 2SSRS IOM M6 Join Date: May 2009
Location: Abbotsford BC Canada
Posts: 11,291
|
Even Ken at Straddle Craft did a little work on Pumpkin today. Manifold cover ready for final sand and a splash of IOM. Pumpkin will look pretty now even with the engine cover off.
__________________
|
09-26-2013, 03:04 PM | #1522 |
OFF THE CHAIN
|
That rear end is so damn sexy Brian, love the plenum also! Is it White or primer?
|
09-28-2013, 11:15 AM | #1523 | |
In The Circle
Drives: 2010 Camaro 2SSRS IOM M6 Join Date: May 2009
Location: Abbotsford BC Canada
Posts: 11,291
|
Quote:
__________________
|
|
09-28-2013, 11:27 AM | #1524 |
In The Circle
Drives: 2010 Camaro 2SSRS IOM M6 Join Date: May 2009
Location: Abbotsford BC Canada
Posts: 11,291
|
Finally I was able to get back to the Hammerhead project to finish it off last night. We were able to take Pumpkin for the first heat cycle on the new diff between rain storms last night. Here are the last few pic's of the install.
__________________
Last edited by Merc; 09-28-2013 at 11:37 AM. |
10-04-2013, 07:24 AM | #1525 |
In The Circle
Drives: 2010 Camaro 2SSRS IOM M6 Join Date: May 2009
Location: Abbotsford BC Canada
Posts: 11,291
|
Bumped for Crude.
__________________
|
10-06-2013, 02:22 AM | #1526 |
In The Circle
Drives: 2010 Camaro 2SSRS IOM M6 Join Date: May 2009
Location: Abbotsford BC Canada
Posts: 11,291
|
Starting to collect parts for winter time mod's. Got to keep up with the Jones. Thanks to JRE.
__________________
Last edited by Merc; 10-06-2013 at 02:39 AM. |
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Can ring and pinion be installed w/ pumpkin in car? | GMRULZ | V8 and V6 Transmissions / Driveline (6L80 / 6L50 / TR6060 / AY6) | 2 | 01-19-2011 07:33 PM |
Pumpkin Fixed | Merc | Canada | 12 | 10-24-2010 08:38 PM |
Nekoosa Pumpkin Fest | blackgoldhtr | USA - Great Lakes | 1 | 10-14-2010 08:18 PM |
Pumpkin Gets Signed | Merc | Canada | 9 | 09-03-2010 11:12 PM |
Pumpkin is moving to the city | Noah | 5th Gen Camaro SS LS LT General Discussions | 0 | 11-27-2009 01:12 PM |