08-16-2019, 05:37 AM | #29 |
|
Hotchkis brace works great and lets exhaust fit.
|
08-24-2019, 08:31 AM | #30 |
Drives: 2014 camaro SS2 convertible Join Date: Sep 2018
Location: washington
Posts: 5
|
I installed corsa dual tips zl1 set up on my 2014 ss convertible ,Love it had to replace rear bumper lower valance and install a new tubular brace because .
|
08-25-2019, 09:48 AM | #31 | |
Drives: 2015 2SS White Convertible CE/INDY Join Date: Mar 2016
Location: Lockport, IL
Posts: 780
|
Quote:
I just put on my ARH LTH and they come down to far and interfere with the front brace. I was able to put it on but it now touches the exhaust pipe. This brace does look like something I could use because the back side of my brace is fine, it's just the front that touch. This SW brace is not as deep and it has a nice notch in it to allow the piping to not touch. I was thinking to cutting and modifying mine but if this one works, then I see no harm in using it. UPDATE: I also found this https://www.moderngenauto.com/Gen-5-...RoCBcoQAvD_BwE But it's way more expensive. I wonder which is better? joe...
__________________
ARH LTH/HFC/Legato muffler, RDP Custom Tune, K&N Blackhawk CAI, Bigworm Blackout kit, ZL1 Rims, Phantom Grills, VMAX PTB
Last edited by GodWentPunk; 08-25-2019 at 10:24 AM. |
|
09-02-2019, 11:25 PM | #32 |
Angewendet Ingenieur
Drives: 14 Camaro ZL1 Join Date: Apr 2015
Location: USA
Posts: 401
|
I installed a full competition 3 inch dynatech exhaust for coupe. Remade the braces, modified the rear section, and everything is fine with bracing in all the original areas.
__________________
————
LQ9, Iron Block, Forged internals, 408CI, Jannetty custom cam, TS short block, Whipple, Hardened Jackshaft, PRC 260, 2X3 Dynatech Full Competition, HF Cats, CAI, NW 103, Chee, ID 1300, COPO Breather, MSD, Fore Dual Pump, ultratorque, E85, dual Meth, True Trac, 3:45, 1500hp axle-shafts, DSS CF, BMR, custom Pearl/Candy paint by Jaidah. |
09-03-2019, 02:59 PM | #33 |
Drives: 2015 2SS White Convertible CE/INDY Join Date: Mar 2016
Location: Lockport, IL
Posts: 780
|
^^^^ In that last pic, are you only using 1 bolt hole from each side? My bracket that I'm trying to build will use 3 bolts per side but in the middle, I'm gutting it out to a point where it's only going to be about 4in thick.
joe...
__________________
ARH LTH/HFC/Legato muffler, RDP Custom Tune, K&N Blackhawk CAI, Bigworm Blackout kit, ZL1 Rims, Phantom Grills, VMAX PTB
|
09-03-2019, 11:03 PM | #34 |
Angewendet Ingenieur
Drives: 14 Camaro ZL1 Join Date: Apr 2015
Location: USA
Posts: 401
|
I replaced the intermediate brace making an “X” brace flat stock and welded in the center which provided better clearance and which I felt is stronger. At some point I will remake these with aluminum stock. The front sheet metal brace was replaced with offset flat stock which can be easily made. The lower rear brace housing needed to be trimmed to clear the mufflers (size will dictate”. No spacers and longer bolts needed.
|
09-08-2019, 07:36 AM | #35 |
Drives: 2015 2SS White Convertible CE/INDY Join Date: Mar 2016
Location: Lockport, IL
Posts: 780
|
Here is my updated brace. I still had to use some washers to clear things.
Joe...
__________________
ARH LTH/HFC/Legato muffler, RDP Custom Tune, K&N Blackhawk CAI, Bigworm Blackout kit, ZL1 Rims, Phantom Grills, VMAX PTB
|
|
|
|
|